TP-LINK TL-WDR4300

From WikiDevi
Jump to: navigation, search

TP-LINK TL-WDR4300 v1.1
Availability: common

FCC approval date: 06 June 2012
(Est.) release date: 13 June 2012
UPC: 845973051938 (UPC DB, On eBay)
Country of manuf.: China

Amazon image

ASIN
B0088CJT4U (Flag of the United States.svg, On Amazon, On CCC)

Type: wireless router

FCC ID: TE7WDR4300
Industry Canada ID: 8853A-WDR4300

Power: 12 VDC, 1.5 A
Connector type: barrel
Conn. measurements: 5.5 mm (OD), 2.1 mm (ID), 9.5 mm (LEN)

CPU1: Atheros AR9344 (560 MHz)
FLA1: 8 MiB
8,388,608 B
65,536 Kib
8,192 KiB
64 Mib
0.00781 GiB
(Spansion S25FL064KIF)
RAM1: 128 MiB
134,217,728 B
1,048,576 Kib
131,072 KiB
1,024 Mib
0.125 GiB
(Hynix H5PS5162GFR × 2)

Expansion IFs: USB 2.0=
USB ports: 2

WI1 chip1: Atheros AR9344
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: RP-SMA
WI2 chip1: Atheros AR9580
WI2 802dot11 protocols: an
WI2 MIMO config: 3x3:3
WI2 antenna connector: RP-SMA

ETH chip1: Atheros AR9344
Switch: Atheros AR8327N
LAN speed: 10/100/1000
LAN ports: 4
WAN speed: 10/100/1000
WAN ports: 1

abgn

Third party firmware supported: OpenWrt, DD-WRT • (List)

Default IP address: 192.168.0.1
the IP 192.168.0.1 is used by 575 additional devices
of which 49 are TP-LINK devices
Default login user: admin
Default login password: admin
admin:admin credentials used by 926 additional devices
of which 165 are TP-LINK devices

802dot11 OUI: C0:4A:00 (2 E, 2 W, 2013)
Ethernet OUI: C0:4A:00 (2 E, 2 W, 2013)

For a list of all currently documented Atheros chipsets with specifications, see Atheros.


N750 Wireless Dual Band Gigabit Router

Product page  • Firmware Interface  • Downloads

See also the TP-LINK TL-WDR4310 which shares the same hardware.

The Mercury MW4530R probably (on the OpenWrt Forums)
also shares the same hardware (minus a USB port).

"2050500224 Rev:1.0" is silkscreened on the board in the FCC photos.

A Genesys Logic GL850G USB 2.0 Hub controller is in use.

Additional external links[edit]

"2050500231 Rev:1.0" is silkscreened on the board photo (v1.1).

PSU[edit]

Power supplies, as shown in the FCC photos, are...

  • US: Leader Electronics MU18-2120150-A1
(100-240VAC ~ 50/60Hz, 0.6A -> 12VDC, 1.5A)
  • Australia: Leader Electronics MU18-2120150-A3
(100-240VAC ~ 50/60Hz, 0.6A -> 12VDC, 1.5A)
  • UK: Leader Electronics MU18-2120150-B2
(100-240VAC ~ 50/60Hz, 0.6A -> 12VDC, 1.5A)
  • Euro: Leader Electronics MU18-2120150-C5
(100-240VAC ~ 50/60Hz, 0.6A -> 12VDC, 1.5A)

JTAG[edit]

AR9344 Support two JTAG modes:

Plain JTAG and EJTAG for debugging.

To enable EJTAG mode you will need to remove

bootstrap resistor marked on this image:

If u-boot is not damaged and you won't to experiment with EJTAG,

then you will need to disable at least /CS pin of SPI chip.
You can see it on this picture too.

Images[edit]