WikiDevi will be going offline 2019-10-31. For historical dumps of the database, see 'WikiDevi' @ the Internet Archive (MW XML, Files, Images).
Final dumps will be made available after the site goes offline.
There is no chance the data will not live on, in some form - even if it isn't 'WikiDevi' anymore. For example, see TechInfoDepot.

Sitecom WLR-6100

From WikiDevi
Jump to: navigation, search

Sitecom WLR-6100 v1

Type: wireless router

Power: 12 VDC, 2 A
Connector type: barrel

CPU1: Ralink RT6856 (700 MHz)
FLA1: 8 MiB
8,388,608 B
65,536 Kib
8,192 KiB
64 Mib
0.00781 GiB
(Macronix MX25L6405D)
RAM1: 64 MiB
67,108,864 B
524,288 Kib
65,536 KiB
512 Mib
0.0625 GiB
(Nanya Model?)

Expansion IFs: USB 2.0
USB ports: 2

WI1 chip1: Ralink RT3593
WI1 802dot11 protocols: an
WI1 MIMO config: 3x3:3
WI1 antenna connector: none
WI2 chip1: Ralink RT3593
WI2 802dot11 protocols: bgn
WI2 MIMO config: 3x3:3
WI2 antenna connector: none

ETH chip1: Ralink RT6856
Switch: Atheros AR8327N
LAN speed: 1G
LAN ports: 4
WAN speed: 1G
WAN ports: 1

abgn

Default IP address: 192.168.0.1
the IP 192.168.0.1 is used by 738 additional devices
of which 13 are Sitecom devices
Default login user: admin
Default login password: blank
admin:blank credentials used by 316 additional devices
of which 2 are Sitecom devices

802dot11 OUI: none specified

For a list of all currently documented Ralink chipsets with specifications, see Ralink.


Wireless N900 Gigabit Dual-Band Router X6

"Sitecom WLR-6100 v1 - 001" is written on label.

Product page

On SpeedGuide

Default IP address: 192.168.0.1
Default login username: admin
Default login password: (sticker on the bottom of the device)

Serial[edit]

Original firmware Boot log (serial)
U-boot Ver:1.0.0.2 2012/11/14 11:07:27

Board: Ralink APSoC DRAM:  64 MB
flash manufacture id: c2, device id 20 17
find flash: MX25L6405D
Flash size 8MB, sector count = 128
============================================ 
ASIC 6855A_MP (Port5<->GigaSW)
Product Name: WLR-6100
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768 
rt6855A_gsw_init: HWCFIST=23009e00

Please choose the operation: 
   1: Load system code to SDRAM via TFTP. 
   3: Boot system code via Flash (default).

   
3: System Boot system code via Flash.
## Booting image at b0050000 ...
   Image Name:   Linux Kernel Image
   Created:      2014-03-06   4:13:37 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1847464 Bytes =  1.8 MB
   Load Address: 80020000
   Entry Point:  80023d30
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

init started: BusyBox v1.13.3 (2014-03-06 12:09:20 CST)
starting pid 740, tty '/dev/console': '/sbin/config_init'
mknod: /dev/ttyS0: File exists
mknod: /dev/ttyS1: File exists
Config Init version: 2.10.20.4 date: 2014/03/06
Wed Jan  1 00:00:00 UTC 2014
ln: /lib/./modules: File exists
starting pid 788, tty '/dev/ttyS0': '/sbin/config_term'
************************************************************************
*                                 WLR-6100                             *
************************************************************************

KernelApp/Ramdisk Ver:2.10.20.4                  Date:2014/03/06
password: 
!!! wrong password !!! 
password: 
!!! wrong password !!!
Boot log (serial) - Ralink SDK firmware (not original firmware)
Linux version 2.6.36 (ris8@ris8-Aspire-5720) (gcc version 3.4.2) #6 Sun Oct 5 01:51:00 CEST 2014
ISPRAM0: PA=002c8000,Size=00008000,enabled
Ralink RT63165 SOC prom init
CPU revision is: 00019555 (MIPS 34Kc)
Determined physical RAM map:
 memory: 03fe0000 @ 00020000 (usable)
Wasting 1024 bytes for tracking 32 unused pages
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000020 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000020 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16224
Kernel command line:  es=1 root=/dev/ram0  console=ttyS0
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00058174
Readback ErrCtl register=00058174
Memory: 58040k/65408k available (2752k kernel code, 7368k reserved, 820k data, 3096k init, 0k highmem)
Hierarchical RCU implementation.
        RCU-based detection of stalled CPUs is disabled.
        Verbose stalled-CPUs detection is disabled.
NR_IRQS:64
CPU frequency 699.00 MHz
console [ttyS0] enabled
Calibrating delay loop... 465.30 BogoMIPS (lpj=2326528)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
start PCIe register access

*************** RT6855A PCIe RC mode *************
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000)
pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
pci 0000:00:01.0: BAR 8: assigned [mem 0x20100000-0x201fffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x2000ffff]
pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x2000ffff] (PCI address [0x20000000-0x2000ffff]
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0:   bridge window [io  disabled]
pci 0000:00:00.0:   bridge window [mem 0x20000000-0x200fffff]
pci 0000:00:00.0:   bridge window [mem pref disabled]
pci 0000:02:00.0: BAR 0: assigned [mem 0x20100000-0x2010ffff]
pci 0000:02:00.0: BAR 0: set to [mem 0x20100000-0x2010ffff] (PCI address [0x20100000-0x2010ffff]
pci 0000:00:01.0: PCI bridge to [bus 02-02]
pci 0000:00:01.0:   bridge window [io  disabled]
pci 0000:00:01.0:   bridge window [mem 0x20100000-0x201fffff]
pci 0000:00:01.0:   bridge window [mem pref disabled]
** bus= 0, slot=0x0
BAR0 at slot 0 = 0
bus=0x0, slot = 0x0
res[0]->start = 0
res[0]->end = 0
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
** bus= 0, slot=0x1
BAR0 at slot 1 = 0
bus=0x0, slot = 0x1
res[0]->start = 0
res[0]->end = 0
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
** bus= 1, slot=0x0
bus=0x1, slot = 0x0
res[0]->start = 20000000
res[0]->end = 2000ffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
** bus= 2, slot=0x1
bus=0x2, slot = 0x1
res[0]->start = 20100000
res[0]->end = 2010ffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RT3xxx EHCI/OHCI init.
fuse init (API version 7.15)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Ralink gpio driver initialized
ttyS0 at I/O 0xbfbf0003 (irq = 1) is a TC3162
brd: module loaded
flash manufacture id: c2, device id 20 17
MX25L6405D(c2 2017c220) (8192 Kbytes)
mtd .name = raspi, .size = 0x00800000 (0M) .erasesize = 0x00000008 (0K) .numeraseregions = 65536
Creating 5 MTD partitions on "raspi":
0x000000000000-0x000000800000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000001000000 : "Kernel"
mtd: partition "Kernel" extends beyond the end of device "raspi" -- size truncated to 0x7b0000
rdm_major = 253
MAC_ADRH -- : 0x0000000c
SMACCR1 -- : 0x0000000c
MAC_ADRL -- : 0x432880fc
SMACCR0 -- : 0x432880fc
Ralink APSoC Ethernet Driver Initilization. v2.1  256 rx/tx descriptors allocated, mtu = 1500!
MAC_ADRH -- : 0x0000000c
SMACCR1 -- : 0x0000000c
MAC_ADRL -- : 0x432880ce
SMACCR0 -- : 0x432880ce
PROC INIT OK!
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x1fbb0000
rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2
rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x1fba1000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (906 buckets, 3624 max)
GRE over IPv4 demultiplexor driver
gre: can't add protocol
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
TCP cubic registered
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Freeing unused kernel memory: 3096k freed
init started: BusyBox vAlgorithmics/MIPS FPU Emulator v1.5
1.12.1 (2014-10-05 01:23:5devpts: called with bogus options
5 CEST)
starting pid 216, tty '': '/etc_ro/rcS'
mount: mounting none on /proc/bus/usb failed: No such file or directory
Welcome to
    _______  _______  ___     __  ____   _  _   ___
    |  ___  \|   __  ||   |   |__||    \ | || | /  /
    | |___| ||  |__| ||   |__  __ |     \| || |/  /
    |   _   /|   _   ||      ||  || |\     ||     \
    |__| \__\|__| |__||______||__||_| \____||_|\___\

                     =System Architecture Department=

starting pid 225, tty '/dev/ttyS0': '/bin/sh'


BusyBox v1.12.1 (2014-10-05 01:23:55 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

# internet.sh
Password for 'admin' changed
rmmod: ralink_wdt: No such file or directory
rmmod: cls: No such file or directory
rmmod: hw_nat: No such file or directory
rmmod: raeth: No such file or directory
insmod: bridge.ko: module not found
insmod: mii.ko: module not found
insmod: raeth.ko: module not found

##### disable 1st wireless interface #####
rmmod: ip_nat_pptp: No such file or directory
rmmod: ip_conntrack_pptp: No such file or directory
ifconfig: ioctl 0x8913 failed: No such device
brctl: bridge br0: No such device or address
/sbin/internet.sh: line 559: iptables: not found
/sbin/internet.sh: line 560: iptables: not found
/sbin/internet.sh: line 561: iptables: not found
##### config Ralink ESW vlan partition (LLLLW) #####
switch reg write offset=2004, value=ff0003
switch reg write offset=2104, value=ff0003
switch reg write offset=2204, value=ff0003
switch reg write offset=2304, value=ff0003
switch reg write offset=2404, value=ff0003
switch reg write offset=2504, value=ff0003
switch reg write offset=2010, value=810000c0
switch reg write offset=2110, value=810000c0
switch reg write offset=2210, value=810000c0
switch reg write offset=2310, value=810000c0
switch reg write offset=2410, value=810000c0
switch reg write offset=2510, value=810000c0
switch reg write offset=2610, value=81000000
switch reg write offset=2710, value=81000000
switch reg write offset=2604, value=20ff0003
switch reg write offset=2704, value=20ff0003
Special Tag Disabled
switch reg write offset=2610, value=81000000
switch reg write offset=2014, value=10001
switch reg write offset=2114, value=10001
switch reg write offset=2214, value=10001
switch reg write offset=2314, value=10001
switch reg write offset=2414, value=10002
switch reg write offset=2514, value=10001
REG_ESW_WT_MAC_ATC is 0x7ff0002
done.

phy_tx_ring = 0x02918000, tx_ring = 0xa2918000

phy_rx_ring0 = 0x02919000, rx_ring0 = 0xa2919000
MAC_ADRH -- : 0x0000000c
SMACCR1 -- : 0x0000000c
MAC_ADRL -- : 0x432880ce
SMACCR0 -- : 0x432880ce
ESW: Link Status Changed - Port5 Link UP
CDMA_CSG_CFG = 81000007
GDMA1_FWD_CFG = C0710000
vconfig: ioctl error for rem: No such device
vconfig: ioctl error for rem: No such device
rmmod: 8021q: No such file or directory
insmod: 8021q.ko: module not found
brctl: iface ra0: No such device
device eth2.1 entered promiscuous mode
device eth2 entered promiscuous mode
udhcpc (v1.12.1) started
br0: port 1(eth2.1) entering learning state
br0: port 1(eth2.1) entering learning state
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
br0: port 1(eth2.1) entering forwarding state
killall: udhcpd: no process killed
Set: phy[0].reg[0] = 3900
Set: phy[1].reg[0] = 3900
Set: phy[2].reg[0] = 3900
Set: phy[3].reg[0] = 3900
Set: phy[0].reg[0] = 3100
Set: phy[1].reg[0] = 3100
Set: phy[2].reg[0] = 3100
Set: phy[3].reg[0] = 3100
rm: cannot remove '/etc/radvd.conf': No such file or directory
/sbin/nat.sh: line 47: iptables: not found
iptables -F -t filter 1>/dev/null 2>&1
iptables -D FORWARD -j macipport_filter 1>/dev/null 2>&1
iptables -F macipport_filter 1>/dev/null 2>&1
iptables -D FORWARD -j web_filter  1>/dev/null 2>&1
iptables -F web_filter  1>/dev/null 2>&1
iptables -D FORWARD -j malicious_filter 1>/dev/null 2>&1
iptables -F malicious_filter  1>/dev/null 2>&1
iptables -D INPUT -j malicious_input_filter 1>/dev/null 2>&1
iptables -F malicious_input_filter  1>/dev/null 2>&1
iptables -P INPUT ACCEPT
sh: iptables: not found
iptables -P OUTPUT ACCEPT
sh: iptables: not found
iptables -P FORWARD ACCEPT
sh: iptables: not found
iptables -t filter -N web_filter 1>/dev/null 2>&1
iptables -t filter -N macipport_filter 1>/dev/null 2>&1
iptables -t filter -N malicious_filter 1>/dev/null 2>&1
iptables -t filter -N synflood_filter 1>/dev/null 2>&1
iptables -t filter -N malicious_input_filter 1>/dev/null 2>&1
iptables -t filter -N synflood_input_filter 1>/dev/null 2>&1
iptables -t filter -A FORWARD -j web_filter 1>/dev/null 2>&1
iptables -t filter -A FORWARD -j macipport_filter 1>/dev/null 2>&1
iptables -t filter -A FORWARD -j malicious_filter 1>/dev/null 2>&1
iptables -t filter -A malicious_filter -p tcp --syn -j synflood_filter 1>/dev/null 2>&1
iptables -t filter -A INPUT -j malicious_input_filter 1>/dev/null 2>&1
iptables -t filter -A malicious_input_filter -p tcp --syn -j synflood_input_filter 1>/dev/null 2>&1
iptables -A FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu 1>/dev/null 2>&1
iptables -A malicious_input_filter -i eth2.2 -p tcp --dport 80 -j DROP
sh: iptables: not found
/bin/super_dmz -f
sh: /bin/super_dmz: not found
iptables -t nat -D PREROUTING -j port_forward 1>/dev/null 2>&1
iptables -t nat -F port_forward  1>/dev/null 2>&1; iptables -t nat -X port_forward  1>/dev/null 2>&1
iptables -t nat -D PREROUTING -j DMZ 1>/dev/null 2>&1
iptables -t nat -F DMZ 1>/dev/null 2>&1; iptables -t nat -X DMZ  1>/dev/null 2>&1
cat /proc/sys/net/netfilter/nf_conntrack_udp_timeout > /var/.udpbackup
echo 0 > /proc/sys/net/netfilter/nf_conntrack_udp_timeout
cat /var/.udpbackup > /proc/sys/net/netfilter/nf_conntrack_udp_timeout; rm -f /var/.udpbackup
cat /proc/sys/net/netfilter/nf_conntrack_tcp_timeout_established > /var/.tcpbackup
echo 0 > /proc/sys/net/netfilter/nf_conntrack_tcp_timeout_established
cat /var/.tcpbackup > /proc/sys/net/netfilter/nf_conntrack_tcp_timeout_established; rm -f /var/.tcpbackup
iptables -t nat -N port_forward 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 1 -j port_forward 1>/dev/null 2>&1
iptables -t nat -N DMZ 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 2 -j DMZ 1>/dev/null 2>&1
ntp.sh
ddns.sh
sh: ddns.sh: not found
kill -9 `cat /var/run/wscd.pid.ra0`
cat: can't open '/var/run/wscd.pid.ra0': No such file or directory
kill: you need to specify whom to kill
iwpriv ra0 set WscConfMode=0 1>/dev/null 2>&1
route delete 239.255.255.250 1>/dev/null 2>&1
killall -9 watchdog 1>/dev/null 2>&1
rmmod ralink_wdt.o
rmmod: ralink_wdt.o: No such file or directory
killall -q klogd
killall -q syslogd
syslogd -C8 1>/dev/null 2>&1
klogd 1>/dev/null 2>&1
killall -q zebra
killall -q ripd
echo 0 > /proc/sys/net/ipv6/conf/all/forwarding
webs: Listening for HTTP requests at address 10.10.10.254

See also[edit]