See 'WikiDevi' @ the Internet Archive (MW XML, Files, Images)
upgraded MW to 1.30 - maybe things are slightly less broken

D-Link DIR-600L rev A1

From WikiDevi
Jump to: navigation, search

D-Link DIR-600L A1

Manuf/OEM/ODM Alpha Networks WRG-N40

FCC approval date: 18 January 2012
(Est.) release date: 02 March 2012
UPC: 790069373596 (UPC DB, On eBay)
Country of manuf.: China

Amazon image

ASIN
B007FECGS8 (Flag of the United States.svg, On Amazon, On CCC)
multiple revisions of this device, use caution

Type: wireless router

FCC ID: KA2IR600LA1
Industry Canada ID: 4216A-IR600LA1

Power: 5 VDC, 1 A
Connector type: barrel

CPU1: Realtek RTL8196C (390 MHz)
FLA1: 4 MiB
4,194,304 B
32,768 Kib
4,096 KiB
32 Mib
0.00391 GiB
(Winbond 25Q32BVSIG)
RAM1: 32 MiB
33,554,432 B
262,144 Kib
32,768 KiB
256 Mib
0.0313 GiB
(Winbond W9825G6JH-6)

Expansion IFs: none specified
JTAG: yes, 12-pin header, JP1, unpopulated, also labled JTAG
Serial: yes, 4-pin header, JP2, unpopulated, 3.3v TTL, (38400,8,N,1)

WI1 chip1: Realtek RTL8188RE
WI1 802dot11 protocols: bgn
WI1 MIMO config: 1x1:1
WI1 antenna connector: none

ETH chip1: Realtek RTL8196C
Switch: Realtek RTL8196C
LAN speed: 10/100
LAN ports: 4
WAN speed: 10/100
WAN ports: 1

bgn

Stock FW OS: Linux 2.4.18

Default IP address: 192.168.0.1
the IP 192.168.0.1 is used by 722 additional devices
of which 207 are D-Link devices
Default login user: admin
Default login password: blank
admin:blank credentials used by 312 additional devices
of which 179 are D-Link devices

802dot11 OUI: 14:D6:4D (8 E, 9 W, 2009), C8:D3:A3 (4 E, 5 W, 2013)
Ethernet OUI: 14:D6:4D (8 E, 9 W, 2009), C8:D3:A3 (4 E, 5 W, 2013)

For a list of all currently documented Realtek chipsets with specifications, see Realtek.
Regarding third party firmware support, Realtek SoC support in OpenWrt
+ (success) RTL8196C port status. on the OpenWrt Forum
and the Realtek thread on the DD-WRT Forum may be of interest.


Wireless N150 Home Cloud Router

Product page  • Support page

"8WRGN40..0B2Z" and a checkbox for the below Alpha Networks

parts is silkscreened on the board.
  • 1WRGN35...A1L
  • 1WRGN40...A1L
  • 1WRGN40...B1L
  • 1DIR600N..B2Z

Possible OUI of 14:D6:4D (it's printed on a label in the FCC photos)

Appears to be running Linux 2.4.18 Kernel

Serial[edit]

  • PCB Has an unpopulated 12-pin header marked JP2
- JTAG, unknown pinout
and a unpopulated 4-pin header marked JP1
- UART Serial (3.3v TTL)

Pinout[edit]

(Square = 1st, Left -> Right)
 ©      ®   ©   ©
 Rx    Vcc GND Tx

Terminal settings: 8N1 @ 38400 / Flow Control: None

Serial port can be connect with USB TO COM PL2303HX adapter.

Just connect 3 pin Rx, Tx and GND.

Set the baudrate at 38400, and connect Rx pin of adapter to Tx pin of router,

Tx pin of adapter to Rx pin of router, GND of adapter to GND of router.

Hidden WebUI pages[edit]

These do not appear to be listed anywhere on the WebUI.

Run system commands: *IP*/shell.asp
Guest Access / Virtual AP Settings: *IP*/Advanced/Guest_Zone.asp

Boot log[edit]

boot log
OK
OK


4.Winbond SPI (4 MByte)!

kldat 2011.12.07-18:31+0900 version v2.8.1f [16](390M)
Jump to 0x80500000...
decompressing kernel:
Uncompressing Linux... done, booting the kernel.
done decompressing kernel.
Creating 4 MTD partitions on "Physically mapped flash":
0x00000000-0x000e0000 : "boot+cfg+linux"
master size 0x004000000x000e0000-0x00330000 : "root fs"
master size 0x004000000x00330000-0x00380000 : "webpage"
master size 0x004000000x00380000-0x00400000 : "mydlink"
master size 0x00400000RTL8192C/RTL8188C driver version 1.9 (2011-03-08)
init started:  BusyBox v1.01 (2012.11.21-02:25+0000) multi-call binary
Starting pid 9, console /dev/ttyS0: '/bin/sh'


BusyBox v1.01 (2012.11.21-02:25+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.

57
mount: Mounting /dev/mtdblock2 on /web-lang failed: Invalid argument
Start service ->: [all]
mount: Mounting /dev/mtdblock2 on /web-lang failed: Invalid argument
mount: Mounting /dev/mtdblock3 on /mydlink failed: Device or resource busy
init start config check
init get mode
exec log script
system reinit
Initialize wlan0 interface
set 615 wlan channel
Initialize wlan0-va0 interface
Setup BRIDGE interface
SIOCGIFFLAGS: No such device
bridge br0 doesn't exist; can't delete it
Setup bridge...
route: SIOC[ADD|DEL]RT: No such process
route: SIOC[ADD|DEL]RT: No such process
route: SIOC[ADD|DEL]RT: No such process
route: SIOC[ADD|DEL]RT: No such process
route: SIOC[ADD|DEL]RT: No such process
route: SIOC[ADD|DEL]RT: No such process
route: SIOC[ADD|DEL]RT: No such process
route: SIOC[ADD|DEL]RT: No such process
route: SIOC[ADD|DEL]RT: No such process

WiFi Simple Config v2.7-wps2.0 (2012.11.21-09:27+0000).

Setup WAN interface

MiniIGD v1.08 (2012.01.04-11:20+0000).

/proc/wan_if: cannot create
killall: netbios: no process killed
killall: llmnresp: no process killed
[: 0: unknown operand
Start telnetd ...
0DevInfo.txt text mode!
hard ver isA1
1452
boa: server version Boa/0.94.14rc21
boa: server built Nov 21 2012 at 17:27:46.
boa: starting server pid=1451, port 80
killall: mydlink-watch-dog.sh: no process killed
killall: signalc: no process killed
killall: tsa: no process killed
opt.local stop ok.
opt.local start ok.
1497
# iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
killall: dnsmasq: no process killed
killall: proxyd: no process killed
Read configuration file /etc/proxyd.conf...
iptables: Bad rule (does a matching rule exist in that chain?)
smart404 stop ok.
Read url configuration file /etc/proxyd_url.conf...
Start http proxy server...
Start server at br0 port 5449

Images[edit]