See 'WikiDevi' @ the Internet Archive (MW XML, Files, Images)
upgraded MW to 1.30 - maybe things are slightly less broken

Cisco DPC3939

From WikiDevi
Jump to: navigation, search

Cisco DPC3939 Comcast 1.0
Availability: common

Manuf/OEM/ODM Pegatron

FCC approval date: 28 May 2013
Country of manuf.: China

Amazon image

ASIN
B00I11LW0W (Flag of the United States.svg, On Amazon, On CCC)

Type: wireless router, cable modem, analog phone gateway

Power: 120 VAC ~ 60 Hz, 1.1 A
Connector type: C7P

CPU1: Intel Puma 6
FLA1: 128 MiB
134,217,728 B
1,048,576 Kib
131,072 KiB
1,024 Mib
0.125 GiB
(Micron MT29F1G08ABADAWP)
FLA2: 32 MiB
33,554,432 B
262,144 Kib
32,768 KiB
256 Mib
0.0313 GiB
(Micron N25Q256A13ESF404F)
RAM1: 512 MiB
536,870,912 B
4,194,304 Kib
524,288 KiB
4,096 Mib
0.5 GiB
(Micron MT41K128M16JT-125:K × 2)

Expansion IFs: USB 2.0
USB ports: 2

WI1 module: Pegatron UPWL60281HP
WI1 module IF: Mini PCIe
WI1 chip1: Atheros AR9381
WI1 802dot11 protocols: bgn
WI1 MIMO config: 3x3:3
WI1 antenna connector: U.FL
WI2 module: Pegatron UPWL6580
WI2 module IF: Mini PCIe
WI2 chip1: Atheros AR9580
WI2 802dot11 protocols: an
WI2 MIMO config: 3x3:3
WI2 antenna connector: U.FL

ETH chip1: Intel Puma 6
Switch: Marvell 88E6172
LAN speed: 10/100/1000
LAN ports: 4

abgn

Flags: DOCSIS 3.0, MoCA 2.0, DECT, ZigBee, battery backup

Default SSID: HOME-XXXX-2.4 (3 addl. devices), HOME-XXXX-5 (3 addl. devices)
Default IP address: 10.0.0.1
the IP 10.0.0.1 is used by 19 additional devices
of which 3 are Cisco devices
Default login user: admin
Default login password: password
admin:password credentials used by 370 additional devices
of which 1 are Cisco devices

802dot11 OUI: none specified

For a list of all currently documented Atheros chipsets with specifications, see Atheros.
For a list of all currently documented Intel chipsets with specifications, see Intel.



DOCSIS 3.0 16x4

The FCC external photos indicate that this cable modem is used with Comcast's Xfinity service.

Cisco Wireless Residential Voice Gateway User Guide
Cisco DPC3939 Data Sheet

Per the FCC internal photos...

  • the SoC used is an Intel Puma 6
  • the GbE Switch is a Marvel 88E6172
  • the RAM appears to be 2x Micron MT29F1G08ABADAWP
  • the DECT module is a DSP Group DCX81AC0BFAE3ENC (DCX81)
  • the MOCA module is a ViXS XConnex XC1030
  • The battery shown in the FCC external photos is a Pegatron PB013 (Li-ion, 10.8V 2600mAh, 28Wh).

The FCC label shows the default SSID pattern is HOME-XXXX-2.4 and HOME-XXXX-5.

Bootlog[edit]

boot log
Cat Mountain - Boot Ram.
Version: 0.1.13 (Jan 26 2013, 21:51:41)

Boot Param memory dump:
[0x1FFC] - 0x00010013
[0x1FF8] - 0x00000001
[0x1FF4] - 0x00000001
[0x1FF0] - 0x00000001
[0x1FEC] - 0x00000001
[0x1FE8] - 0x10000000
[0x1FE4] - 0x10000000
[0x1FE0] - 0x0021F000
[0x1FDC] - 0x0023F000
[0x1FD8] - 0x030A0000
[0x1FD4] - 0x00040000
[0x1FD0] - 0x030E0000
[0x1FCC] - 0x030E0000
[0x1FC8] - 0x00020000
[0x1FC4] - 0x00000000
[0x1FC0] - 0x00000000
[0x1FBC] - 0x00000000
[0x1FB8] - 0x00000000
[0x1FB4] - 0x00000000
[0x1FB0] - 0x00000000
[0x1FAC] - 0x00000000
[0x1FA8] - 0x00000000
[0x1FA4] - 0x00000000
[0x1FA0] - 0x00000000
[0x1F9C] - 0x0D0C0908
[0x1F98] - 0x010A0F0E
[0x1F94] - 0x0B050302
[0x1F90] - 0x00000002
[0x1F8C] - 0x00000004
[0x1F88] - 0x000517B6
[0x1F84] - 0x00200000
[0x1F80] - 0x00000070
[0x1F7C] - 0x00220000
[0x1F78] - 0x00020000
[0x1F74] - 0x00000020
[0x1F70] - 0x00080800
[0x1F6C] - 0x00010000
[0x1F68] - 0x00090800
[0x1F64] - 0x00009400
[0x1F60] - 0x00099C00
[0x1F5C] - 0x00065400
[0x1F58] - 0x000FF800
[0x1F54] - 0x00000800
[0x1F50] - 0x00100000
[0x1F4C] - 0x00000800
[0x1F48] - 0x000FF000
[0x1F44] - 0x00000800
[0x1F40] - 0x00000000
Load U-Boot from eMMC/NAND Flash
eMMC/NAND copy from 0x030A0000 to 0x51FB0000 (len:262144).
Done.


U-Boot 1.2.0-g1a0473cf-dirty (May  3 2013 - 08:43:46) Cisco-Boot 3.4.19

DRAM:  256 MB
*** Warning - Unsupported Flash detected, flash is unusable

Manufacturer ID: 0xFF
Type: 0xFF
Density: 0xFF
Extended ID: {0xFF, 0xFF}
failed to probe Flash (bank 0)
Error: failed to probe Flash
Flash:  0 kB
MMC:   sdhci_puma6: 0
MMC info:
  Manufacturer ID: 0
  OEM ID: 0
  Name: MMC128
  MMC version 4.4
  High Capacity: No
  Dual Data Rate (DDR): No
  Bus Width: 8-bit
  Clock: 50000000
  Rd Block Len: 512
  Capacity: 112.4 MB (117833728 bytes)
In:    serial
Out:   serial
Err:   serial
Setting Board-Type to 1
Read AID 2
set ACTIMAGE to 2
Press SPACE to abort autoboot in 2 second(s)
*** ACTIMAGE = 2, will try to boot UBFI2 stored @0x03440000
## Executing script at 03440000
========== Running script (puma6) ver 2.5 =========
*** Running from UBFI2 partition @0x52000000 (eMMC)
Load address ............. 0x3442310
Kernel partition offset .. 0x2360
kernel size .............. 0x1640a0
Root FS partition offset . 0x166400
Root FS size ............. 0x72c400
Additional FS ............ ,0x4c7800(FS1)ro
========== Script Done ============================

*** UBFI2 bootscript executed successfully.
Start booting...
## Booting image at 03442310 ...
ARM MBX sending 'eMMC done.' notification...
   Image Name:   Multi Image File
   Image Type:   ARM Linux Multi-File Image (uncompressed)
   Data Size:    13991088 Bytes = 13.3 MB
   Load Address: 00a00000
   Entry Point:  00a00000
   Contents:
   Image 0:  1458336 Bytes =  1.4 MB
   Image 1:  7521280 Bytes =  7.2 MB
   Image 2:  5011456 Bytes =  4.8 MB
OK

Starting kernel ...

Starting LZMA Uncompression Algorithm.
Compressed file is LZMA format.
[Debug - Kerenl] LZMA Uncompression - Done.
Linux version 2.6.39.3 (root@build6-usg) (gcc version 4.6.1 (Buildroot 2011.08-ga9b374f) ) #1 PREEMPT Wed Feb 19 14:17:47 EST 2014
CPU: ARMv6-compatible processor [410fb764] revision 4 (ARMv7), cr=00c538ff
CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: puma6
Ignoring unrecognised tag 0x00000000
Memory policy: ECC disabled, Data cache writeback
Reserved 2048k DSP memory starting from Physical 0x5fe00000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64516
Kernel command line: root=/dev/mmcblk0p13 rootwait ro nvram=/dev/mmcblk0p10 fs1=/dev/mmcblk0p15 console=ttyS0,115200n8 ethaddr0= usbhostaddr=00.00.00.00.00.00 boardtype=0x00000001 eth0_mdio_phy_addr= ext_switch_reset_gpio= threadirqs
Puma6 boardtype Id 1
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 254MB = 254MB total
Memory: 253316k/253316k available, 6780k reserved, 129024K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
    vmalloc : 0x58800000 - 0x60000000   ( 120 MB)
    lowmem  : 0x50000000 - 0x58000000   ( 128 MB)
    pkmap   : 0x4fe00000 - 0x50000000   (   2 MB)
    modules : 0x4f000000 - 0x4fe00000   (  14 MB)
      .init : 0x50018000 - 0x50039000   ( 132 kB)
      .text : 0x50039000 - 0x503fa068   (3845 kB)
      .data : 0x503fc000 - 0x5041b640   ( 126 kB)
Preemptable hierarchical RCU implementation.
	RCU-based detection of stalled CPUs is disabled.
	Verbose stalled-CPUs detection is disabled.
NR_IRQS:150
Interrupt controller revision : 4e822100
Initialized Peripheral Port Remap Register to base : 0x20000000
Puma-6 system_rev = 1505 -- docsis ip rev = 16
CRU 13 is allready in CRU state 3 [ignore operation]
Puma6 Timer0 initialized
console [ttyS0] enabled
Calibrating delay loop... 447.28 BogoMIPS (lpj=2236416)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
hw perfevents: enabled with v6 PMU driver, 3 counters available
NET: Registered protocol family 16
hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.

PAL_cppi4Init : domain is 0, cfg ptr is 0x504079F4
PAL_cppi4Init: CPPI 4.1 API initialized successfully.
avalanche_ppd_init: PP system  initialized successfully.

PAL_cppi4Init : domain is 0, cfg ptr is 0x00000000
HW Mutex: Intel(R) HW MUTEX driver built on Feb 19 2014 @ 14:17:29
HW Mutex: pmaster 0x5782b680 ,irq_num 74, reg_base 0xdffe1800
HW Mutex: driver is running. HW MUTEX Code-Id = 0x1000c936
bio: create slab <bio-0> at 0
i2c-gpio i2c-gpio.1: using pins 45 (SDA) and 44 (SCL)
HIL Core: Profile intrusive has been Loaded.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
DECT drv initializing
DECT Page drv succeeded in registering character device page_button Major = 254, Minor = 0
DECT Page drv succeeded in registering character device page_button Major = 254, Minor = 0
GPIO Succeeded in registering character device docsis_gpio_dev Major = 253, Minor = 0
IOSFSB Succeeded in registering character device docsis_iosfsb_drv Major = 252, Minor = 0
p_unit_drv_init:805 Character device p_unit Major = 251, Minor = 0 has been registered
0 = result from request_irq
P-UNIT : Enable reset event handling ...

==============================================================================
P-UNIT : FW version is [ 1.0.9 ] Silicon Stepping [A0]
P-UNIT : Last reset reason   = 0x00000001 [ RESET_COLD_RESET               ]
P-UNIT : Last reset origin   = 0x00000002 [ RESET_ORIGIN_ATOM              ]
P-UNIT : Last reset duration = 0.0 Seconds
==============================================================================
enable IRQ #13 for device named arm_atom_mbx
highmem bounce pool size: 64 pages
squashfs: version 4.0 (2009/01/31) Phillip Lougher
NTFS driver 2.1.30 [Flags: R/W].
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 242
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x70003 (irq = 9) is a TI 16550A
serial8250: ttyS1 at MMIO 0x50003 (irq = 7) is a TI 16550A
serial8250: ttyS2 at MMIO 0x60003 (irq = 8) is a TI 16550A
TI LED driver initialized [major=248]
PUMA6 SPI Controller: Control Reg        [0xDFFE0100]: 0x44453401
PUMA6 SPI Controller: Split Reg          [0xDFFE0104]: 0x00000008
PUMA6 SPI Controller: Current Address Reg[0xDFFE0108]: 0x00000000
PUMA6 SPI Controller: Addressing mode set to: 3
Serial Flash [Bus:0 CS:0] : No device found
Serial Flash [Bus:0 CS:1] : No device found
PUMA6 SPI Controller driver at 0xdffe0100 bus_num = 0x0
(null): TI Codec SPI Controller driver at 0xd01200c8           (irq = 0)
i2c /dev entries driver
watchdog: TI Avalanche Watchdog Timer: timer margin 35 sec
cpuidle: using governor ladder
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
NP-CPU MBX waits for 'eMMC advance mode ready' notification from APP-CPU ...
receive_specific_event_notification Event=0x4  parameter = 0x30
NP-CPU MBX received 'eMMC advance mode ready' notification from APP-CPU.
mmc0: SDHCI controller on platform [sdhci-puma6.0] using ADMA
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (3958 buckets, 15832 max)
ctnetlink v0.93: registering with nfnetlink.
IPVS: Registered protocols ()
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: Creating netns size=744 id=0
IPVS: ipvs loaded.
IPv4 over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
NET: Registered protocol family 15
Bridge firewalling registered
Ebtables v2.0 registered
L2TP core driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFP support v0.3: not present
Waiting for root device /dev/mmcblk0p13...
mmc0: new high speed MMC card at address 0001
mmcblk0: mmc0:0001 MMC128 112 MiB
 mmcblk0: p1 p2 p3 p4 < p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 >
NP-CPU MBX Send notification to APP-CPU - 'Card initialization complete'...
VFS: Mounted root (squashfs filesystem) readonly on device 179:13.
Freeing init memory: 132K
init started: BusyBox v1.19.2 (2014-02-19 14:17:01 EST)
starting pid 35, tty '/dev/tts/0': '/etc/init.d/rcS > /dev/console 2> /dev/console'

About to initialize PP ...

Initializing ppd driver module

PAL_cppi4Init : domain is 0, cfg ptr is 0x00000000

PAL_cppi4Init : domain is 0, cfg ptr is 0x00000000
avalanche_prefetcher_init(1135):return code 0x00
main(149): hal_pp_fw_download SUCCESS!
Removing ppd driver module

The PP Should be running now ...

/dev/mmcblk0p10: recovering journal
/dev/mmcblk0p10 has been mounted 1 times without being checked, check forced.
/dev/mmcblk0p10: 97/256 files (10.3% non-contiguous), 1253/2048 blocks
The device /dev/mmcblk0p10 was scan with fsck.ext3 and the return value is 0
kjournald starting.  Commit interval 5 seconds
EXT3-fs (mmcblk0p10): using internal journal
EXT3-fs (mmcblk0p10): mounted filesystem with ordered data mode
mount -t ext3 /dev/mmcblk0p10 /nvram -o barrier=1
fss=/dev/mmcblk0p15-FS1
/etc/init.d/rcS: /etc/config: line 2114: CROSS: not found


========================================================
Intel CGWSDK release 4.1.1.23
Build date: Wednesday, February 19 2014, 14:25:01
Copyright � 2011, Intel Corporation.
========================================================


Using DOCSIS MAC Manager parameters: -x -m
Start Core Dump (sys_startup.sh) ...
pcd: (264): Starting TI Process Control Daemon.
pcd: (264): Error: Multiple definitions of rule BBU_LASTRULE, ignoring.
pcd: (264): Loaded 123 rules.
pcd: Initialization complete.

Please press Enter to activate this console. sync_app_np_reboot: Starting SYNC-APP-NP-REBOOT Daemon
pcd: (265): Starting process insmod (Rule PUMA6SYSTEM_PROC_BOOTPARAM).
pcd: (265): Starting process /usr/sbin/mocadlfw (Rule PUMA6SYSTEM_MOCA_DLFW).
pcd: (265): Starting process insmod (Rule PUMA6SYSTEM_L2SW_INSMODE).
pcd: (265): Starting process /usr/sbin/watchdog_rt (Rule SYSTEM_WATCHDOG).
pcd: (265): Starting process /usr/sbin/logger (Rule SYSTEM_LOGGER).
pcd: (265): Starting process /usr/sbin/gptimer (Rule SYSTEM_GPTIMER).
TI Watchdog-RT daemon started <kick interval = 10 seconds>
pcd: (265): Rule SYSTEM_WATCHDOG: Success (Process /usr/sbin/watchdog_rt (271)).
main:801 (pid=273): Initialized successfully, timer tick 50ms
pcd: (265): Rule SYSTEM_GPTIMER: Success (Process /usr/sbin/gptimer (273)).

PAL_cppi4Init : domain is 0, cfg ptr is 0x00000000

PAL_cppi4Init : domain is 0, cfg ptr is 0x00000000
PP Operation TI_PPM_PID_CREATED, pid_handle=0

PAL_cppi4Init : domain is 0, cfg ptr is 0x00000000
PP Operation TI_PPM_PID_CREATED, pid_handle=1
pcd: (265): Rule PUMA6SYSTEM_L2SW_INSMODE: Success (Process insmod (270)).
pcd: (265): Starting process echo (Rule PUMA6SYSTEM_L2SWDATA_IRQ_PO).
pcd: (265): Rule PUMA6SYSTEM_L2SWDATA_IRQ_PO: Success (Process echo (280)).
pcd: (265): Starting process /usr/sbin/l2switchd (Rule PUMA6SYSTEM_L2SWITCH).
pcd: (265): Rule PUMA6SYSTEM_PROC_BOOTPARAM: Success (Process insmod (268)).
xb1030_start_fw:149 (pid=269): xb1030_start_fw 1

xb1030_start_fw:152 (pid=269): xb1030_start_fw 2

xb1030_start_fw:156 (pid=269): xb1030_start_fw 3

xb1030_start_fw:161 (pid=269): xb1030_start_fw 4

xb1030_start_fw:165 (pid=269): xb1030_start_fw 5

xb1030_start_fw:172 (pid=269): xb1030_start_fw->timestamp: before download fw 20240000 (us)

read_image:57 (pid=269): Image /usr/sbin/DeloreanProcCImageMoca_Part0.mem size 8, head of data

xb1030_download_fw:96 (pid=269): xb1030_download_fw 1

download_fw:67 (pid=269): size=8

xb1030_download_fw:101 (pid=269): xb1030_download_fw 2

read_image:57 (pid=269): Image /usr/sbin/DeloreanProcCImageMoca_Part1.mem size 62960, head of data

xb1030_download_fw:108 (pid=269): xb1030_download_fw 3

download_fw:67 (pid=269): size=62960

Autoconfiguration disabled for l2sm0
Autoconfiguration disabled for l2sm0.1
pcd: (265): Rule PUMA6SYSTEM_L2SWITCH: Success (Process /usr/sbin/l2switchd (281)).
pcd: (265): Starting process /sbin/ifconfig (Rule PUMA6SYSTEM_MOCA_IFCONFIG).
Autoconfiguration disabled for l2sd0
**** ---- >>>> l2sw_netdev_rx_complete - name "kworker/0:1", pid 32
pcd: (265): Rule PUMA6SYSTEM_MOCA_IFCONFIG: Success (Process /sbin/ifconfig (288)).
xb1030_download_fw:113 (pid=269): xb1030_download_fw 4

read_image:57 (pid=269): Image /usr/sbin/DeloreanProcDImageMoca_Part0.mem size 8, head of data

xb1030_download_fw:120 (pid=269): xb1030_download_fw 5

download_fw:67 (pid=269): size=8

xb1030_download_fw:125 (pid=269): xb1030_download_fw 6

read_image:57 (pid=269): Image /usr/sbin/DeloreanProcDImageMoca_Part1.mem size 192620, head of data

xb1030_download_fw:132 (pid=269): xb1030_download_fw 7

download_fw:67 (pid=269): size=192620

TI Logger: Init complete
[INFO] [COMMON_COMPONENTS.MOCA(pid=269)]: xb1030_download_fw 8
[INFO] [COMMON_COMPONENTS.MOCA(pid=269)]: xb1030_start_fw->timestamp: after download fw 25410000 (us), time used 5170000 (us). take proc C out of soft reset
[INFO] [COMMON_COMPONENTS.MOCA(pid=269)]: xb1030_start_fw 6
[INFO] [COMMON_COMPONENTS.MOCA(pid=269)]: xb1030_clear_control_structure 8
[INFO] [COMMON_COMPONENTS.MOCA(pid=269)]: xb1030_start_fw 7
[INFO] [COMMON_COMPONENTS.MOCA(pid=269)]: xb1030_start_fw 8
pcd: (265): Rule SYSTEM_LOGGER: Success (Process /usr/sbin/logger (272)).
pcd: (265): Starting process /usr/sbin/ext_switch_init (Rule PUMA6SYSTEM_EXTSWITCH_INIT).
pcd: (265): Starting process /usr/sbin/gim (Rule SYSTEM_GIM).
[INFO] [COMMON_COMPONENTS.GIM(pid=292)]: GIM initializing...
pcd: (265): Rule SYSTEM_GIM: Success (Process /usr/sbin/gim (292)).
pcd: (265): Rule SYSTEM_LASTRULE: Success.
pcd: (265): Rule PUMA6SYSTEM_EXTSWITCH_INIT: Success (Process /usr/sbin/ext_switch_init (291)).
pcd: (265): Starting process /bin/sh (Rule BBU_INITDRV).
pcd: (265): Rule GW_APPRUN: Success.
pcd: (265): Starting process gw_prov_utopia (Rule GW_GWPROV).
[INFO] [COMMON_COMPONENTS.GIM(pid=292)]: GIM initialization complete. GIM_MODULE=3086
BBU Kernel module - installing
[INFO] [COMMON_COMPONENTS.EXT_SWITCH(pid=291)]: main - 69 Initialized external switch DB
CRU 10 is allready in CRU state 3 [ignore operation]
BBU Bbu_HalInit end
BBU Kernel module installed - 0
pcd: (265): Rule BBU_INITDRV: Success (Process /bin/sh (293)).
pcd: (265): Starting process /usr/sbin/bbusm (Rule BBU_SM).

********Bbu_updateTemperatureTable: boardRev=7, HwRevision=1, HwPatch=0

 NEW BOARD
[INFO] [COMMON_COMPONENTS.BBU(pid=303)]: Starting main of BBU MSM.....
[INFO] [COMMON_COMPONENTS.BBU(pid=303)]: BBU_InitDataB start
pcd: (265): Rule BBU_SM: Success (Process /usr/sbin/bbusm (303)).
[INFO] [COMMON_COMPONENTS.BBU(pid=303)]: BBU_InitDataBase succeeded data address 0x44c04d0
[INFO] [COMMON_COMPONENTS.BBU(pid=303)]: Data initialized
[ERROR] [COMMON_COMPONENTS.BBU(pid=303)]: BBU reports no battery is inserted
[WARNING] [COMMON_COMPONENTS.BBU(pid=303)]: BBU init - Database assumed to be corrupted , reset cause = reset tbd
[INFO] [COMMON_COMPONENTS.BBU(pid=303)]: System Reset completed
[ERROR] [COMMON_COMPONENTS.BBU(pid=303)]: BBU reports no battery is inserted
pcd: (265): Starting process /usr/sbin/moca_pwr_save (Rule BBU_MOCAPSM).
pcd: (265): Starting process /bin/sh (Rule BBU_DLMRMMOD).
pcd: (265): Rule BBU_LASTRULE: Success.
main:259> Running in background
pcd: (265): Rule BBU_MOCAPSM: Success (Process /usr/sbin/moca_pwr_save (306)).
[INFO] [COMMON_COMPONENTS.BBU(pid=303)]: Initialization complete
pcd: (265): Rule BBU_DLMRMMOD: Success (Process /bin/sh (307)).
[INFO] [COMMON_COMPONENTS.BBU(pid=303)]: Emergency does not exist
[WARNING] [COMMON_COMPONENTS.BBU(pid=303)]: Dest point for reporting bbu event not set
[WARNING] [COMMON_COMPONENTS.BBU(pid=303)]: Dest point for reporting bbu event not set
[INFO_VERBOSE] [COMMON_COMPONENTS.BBU(pid=303)]: Polling timer = 1000
[ERROR] [COMMON_COMPONENTS.BBU(pid=303)]: BBU reports no battery is inserted
[ERROR] [GW.PROV(pid=294)]: GW - Started
*******************************************************************
*
* Copyright (c) 2010 by Cisco Systems, Inc. All Rights Reserved.
*
*******************************************************************
grep: /etc/drg_version.txt: No such file or directory
[utopia][init] Tweaking network parameters
[utopia][init] Starting udev..
[utopia][init] Starting syscfg using file store (/nvram/syscfg.db)
[utopia][init] Starting system logging
[utopia][init] Starting sysevent subsystem
syseventd (330): /proc/330/oom_adj is deprecated, please use /proc/330/oom_score_adj instead.
[utopia][init] Setting any unset system values to default
[utopia][init] Applying iptables settings
NAT Table update all sessions flushed
NAT Table update all sessions flushed
[utopia][init] Processing registration
pcd: (265): Rule PUMA6SYSTEM_MOCA_DLFW: Success (Process /usr/sbin/mocadlfw (269)).
88E6172: Do not egress flood unicast with unknown DA
main:587> swctl_writePortRegister success: wrote: 0x007b
[INFO] [GW.PROV(pid=294)]: GW - Waiting for Docsis INIT
pcd: (265): Rule GW_GWPROV: Success (Process gw_prov_utopia (294)).
pcd: (265): Rule GW_LASTRULE: Success.
pcd: (265): Starting process /etc/scripts/moca_enable.sh (Rule PUMA6SYSTEM_MOCA_START).
pcd: (265): Rule PREDOCSIS_LASTRULE: Success.
pcd: (265): Starting process echo (Rule DOCSIS_APPRUN).
pcd: (265): Rule DOCSIS_APPRUN: Success (Process echo (411)).
pcd: (265): Starting process /usr/sbin/docsis_init_once (Rule DOCSIS_INITONCE).
moca_enabled is set to 1
moca_scan_enabled is set to 0
moca_node_taboo_enabled is set to 0
moca_preferred_nc is set to 1
moca_mixed_mode is set to 1
moca_enable_privacy is set to 0
moca_password_seed is set to 99999999988888888
moca_beacon_pwr_level is set to 9
moca_maximum_tx_power is set to 10
moca_pwr_apc_enable is set to 1
moca_phy_rate is set to 235
moca_freq_plan is set to 1150
mocactld:main:183> enable: 1 run_in_foreground: 0
mocactld:main:186> Running in background
pcd: (265): Rule PUMA6SYSTEM_MOCA_START: Success (Process /etc/scripts/moca_enable.sh (410)).
[INFO_VERBOSE] [DOCSIS.PROD_DB(pid=413)]: Restoring production DB from NVRAM ... SUCCESS
iniparser: cannot open /var/tmp/lsddb_rt.ini
[INFO] [COMMON_COMPONENTS.LSDDB(pid=413)]: LSDDB - Created /var/tmp/lsddb_rt.ini
[INFO] [DOCSIS.NVRAM_DB(pid=413)]: Restoring NVRAM DB from NVRAM ... SUCCESS
[INFO_VERBOSE] [DOCSIS.QOS(pid=413)]: qos_intDb_ResetTaDbRow:  DSX TA entry removal. DB Index = 0, TA ID = 0x0.
[INFO_VERBOSE] [DOCSIS.QOS(pid=413)]: qos_intDb_ResetTaDbRow:  DSX TA entry removal. DB Index = 1, TA ID = 0x0.
[INFO_VERBOSE] [DOCSIS.QOS(pid=413)]: qos_intDb_ResetTaDbRow:  DSX TA entry removal. DB Index = 2, TA ID = 0x0.
[INFO_VERBOSE] [DOCSIS.QOS(pid=413)]: qos_intDb_ResetTaDbRow:  DSX TA entry removal. DB Index = 3, TA ID = 0x0.
[INFO_VERBOSE] [DOCSIS.QOS(pid=413)]: qos_intDb_ResetTaDbRow:  DSX TA entry removal. DB Index = 4, TA ID = 0x0.
[INFO_VERBOSE] [DOCSIS.QOS(pid=413)]: qos_intDb_ResetTaDbRow:  DSX TA entry removal. DB Index = 5, TA ID = 0x0.
[INFO_VERBOSE] [DOCSIS.QOS(pid=413)]: qos_intDb_ResetTaDbRow:  DSX TA entry removal. DB Index = 6, TA ID = 0x0.
[INFO_VERBOSE] [DOCSIS.QOS(pid=413)]: qos_intDb_ResetTaDbRow:  DSX TA entry removal. DB Index = 7, TA ID = 0x0.
[INFO_VERBOSE] [DOCSIS.QOS(pid=413)]: qos_intDb_ResetTaDbRow:  DSX TA entry removal. DB Index = 8, TA ID = 0x0.
[INFO_VERBOSE] [DOCSIS.QOS(pid=413)]: qos_intDb_ResetTaDbRow:  DSX TA entry removal. DB Index = 9, TA ID = 0x0.
[INFO] [VENDOR.SA(pid=413)]: SaDocsis DB saCmUSBonding Param restored from nvram
sched `ps | grep -v grep | grep irq | grep irq/24 | cut -c-5` 1 1
[INFO] [VENDOR.SA(pid=413)]: len 4, addr 0x4274d84
[INFO] [VENDOR.SA(pid=413)]: SaDocsis DB saCmDSBonding Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 4, addr 0x4274d88
[INFO] [VENDOR.SA(pid=413)]: SaDocsis DB saCmForcedDualscan Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 4, addr 0x4274d8c
[INFO] [VENDOR.SA(pid=413)]: SaDocsis DB saCmResiliencyInterval Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 4, addr 0x4274d90
[INFO] [VENDOR.SA(pid=413)]: SaDocsis DB saCmAPMulticastPromiscuous Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 4, addr 0x4274d94
[INFO] [VENDOR.SA(pid=413)]: SaDocsis DB SadbMD5digest Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 16, addr 0x4274d98
[INFO] [VENDOR.SA(pid=413)]: SaDocsis DB saCmBondedResiliencyInterval Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 4, addr 0x4274da8
[INFO] [VENDOR.SA(pid=413)]: SaDocsis DB saCmT4Time Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 4, addr 0x4274dac
[INFO] [VENDOR.SA(pid=413)]: SaDocsis DB saLinkLedTreat Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 4, addr 0x4274db0
[INFO] [VENDOR.SA(pid=413)]: SaDocsis DB saCmDocsisLock Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 4, addr 0x4274db8
pcd: (265): Rule DOCSIS_INITONCE: Success (Process /usr/sbin/docsis_init_once (413)).
pcd: (265): Starting process insmod (Rule DOCSIS_SOCIFDRV).
[INFO] [VENDOR.SA(pid=413)]: SaDocsis DB saPUFFrequency Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 384, addr 0x4274dbc
pcd: (265): Starting process /usr/sbin/cm_status (Rule DOCSIS_CMSTATUS).
pcd: (265): Rule DOCSIS_CMSTATUS: Success (Process /usr/sbin/cm_status (442)).
[INFO] [VENDOR.SA(pid=413)]: Mdd IpMode Override Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 4, addr 0x4274f3c
PAL_cppi4Init : domain is 0, cfg ptr is 0x00000000
RX Init CPPI: open free descriptor queue
RX Init CPPI: allocate descriptors
init_cppi_rx: Allocate descriptors to the embedded free queues

[INFO] [VENDOR.SA(pid=413)]: Mdd IpMode Override Param Last TimeRX Init CPPI: Fill free discriptor queue
 restored from nRX Init CPPI: Set DMA channel
vraminit_cppi_rx: Call PAL_cppi4RxChOpen channel=12, REF_CNT=0 BUF COUNT=512
RX Init CPPI: Init accumulator
RX Init RX CPPI pass
TX Init CPPI: open free descriptor queue
TX Init CPPI: allocate descriptors
init_cppi_tx: Allocate descriptors to the embedded free queues

TX Init CPPI: Fill free discriptor queue
TX Init CPPI: Create CPGMAC TX handler
[INFO] [VENDOR.STX Init CPPI: open mpeg TX channel
A(pid=413)]: lenTX Init CPPI pass
 4, addr 0x4275034 WQ Init CPPI: open queue descriptor queue
WQ Init pass
MPEG driver initialization complete.

pcd: (265): Rule DOCSIS_SOCIFDRV: Success (Process insmod (441)).
[INFO] [VENDOR.SA(pid=413)]: SaDocsis DB saCmResiliencyInterval New Version restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 4, addr 0x4275040
[INFO] [VENDOR.SA(pid=413)]: SaDocsis DB saCmResiliencyInterval New Version restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 4, addr 0x4275044
[INFO] [VENDOR.SA(pid=413)]: SaDocsis DB Sa_runTodOnce Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 4, addr 0x4275048
[INFO] [VENDOR.SA(pid=413)]: SaDocsis DB SaTodTimeInterval Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 4, addr 0x427504c
[INFO] [VENDOR.SA(pid=413)]: SaDocsis DB SaTodVendorIsUp Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 4, addr 0x4275050
[INFO] [VENDOR.SA(pid=413)]: SaDocsis DB cmAPMulticastPromiscuousMode Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 4, addr 0x4275058
[INFO] [VENDOR.SA(pid=413)]: Oor Dsid Override restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 4, addr 0x427505c
[INFO] [VENDOR.SA(pid=413)]: SaDocsis DB saCmFactoryMode Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 4, addr 0x4275064
[INFO] [VENDOR.SA(pid=413)]: Restoring SaDocsis DB from NVRAM ... SUCCESS
[INFO] [VENDOR.SA(pid=413)]: SaRemoteAccess DB APWebSwitch Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 4, addr 0x4275068
[INFO] [VENDOR.SA(pid=413)]: SaRemoteAccess DB WALuser Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 40, addr 0x427506c
[INFO] [VENDOR.SA(pid=413)]: SaRemoteAccess DB WALpass Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 40, addr 0x4275094
[INFO] [VENDOR.SA(pid=413)]: SaRemoteAccess DB WALevel Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 4, addr 0x42750bc
[INFO] [VENDOR.SA(pid=413)]: SaRemoteAccess DB WAdvType Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 4, addr 0x42750c0
[INFO] [VENDOR.SA(pid=413)]: SaRemoteAccess DB WAdvuser Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 40, addr 0x42750c4
[INFO] [VENDOR.SA(pid=413)]: SaRemoteAccess DB WAdvpass Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 40, addr 0x42750ec
[INFO] [VENDOR.SA(pid=413)]: SaRemoteAccess DB WASuperpass Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 40, addr 0x427514c
[INFO] [VENDOR.SA(pid=413)]: SaRemoteAccess DB WASuperpasslen Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 4, addr 0x4275174
[INFO] [VENDOR.SA(pid=413)]: Restoring SaRemoteAccess DBfrom NVRAM ... SUCCESS
[INFO] [VENDOR.SA(pid=413)]: SaPermanent DB ManufactureDate Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 40, addr 0x42751c8
[INFO] [VENDOR.SA(pid=413)]: SaPermanent DB FactoryId Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 40, addr 0x42751f0
[INFO] [VENDOR.SA(pid=413)]: SaPermanent DB PowerSupply Param restored from nvram
[INFO] [VENDOR.SA(pid=413)]: len 4, addr 0x4275218
[INFO] [VENDOR.SA(pid=413)]: Restoring SaPermanent DB from NVRAM ... SUCCESS
[INFO] [VENDOR.SA(pid=413)]: Restoring SaHardwareInfo DB from NVRAM ... SUCCESS
[INFO] [VENDOR.SA(pid=413)]: Restoring SaWifiInfo DB from NVRAM ... SUCCESS
[INFO_VERBOSE] [DOCSIS.INIT(pid=413)]: ------------------ DS Ports Mapping -----------------------------
[INFO_VERBOSE] [DOCSIS.INIT(pid=413)]: LastActualPort=24
[INFO_VERBOSE] [DOCSIS.INIT(pid=413)]:  DS-index-1 map to PHY-Rx-0 and HSIF-16
[INFO_VERBOSE] [DOCSIS.INIT(pid=413)]:  DS-index-2 map to PHY-Rx-1 and HSIF-17
[INFO_VERBOSE] [DOCSIS.INIT(pid=413)]:  DS-index-3 map to PHY-Rx-2 and HSIF-18
[INFO_VERBOSE] [DOCSIS.INIT(pid=413)]:  DS-index-4 map to PHY-Rx-3 and HSIF-19
[INFO_VERBOSE] [DOCSIS.INIT(pid=413)]:  DS-index-5 map to PHY-Rx-8 and HSIF-20
[INFO_VERBOSE] [DOCSIS.INIT(pid=413)]:  DS-index-6 map to PHY-Rx-9 and HSIF-21
[INFO_VERBOSE] [DOCSIS.INIT(pid=413)]:  DS-index-7 map to PHY-Rx-10 and HSIF-22
[INFO_VERBOSE] [DOCSIS.INIT(pid=413)]:  DS-index-8 map to PHY-Rx-11 and HSIF-23
[INFO_VERBOSE] [DOCSIS.INIT(pid=413)]:  DS-index-9 map to PHY-Rx-12 and HSIF-24
[INFO_VERBOSE] [DOCSIS.INIT(pid=413)]:  DS-index-10 map to PHY-Rx-13 and HSIF-25
[INFO_VERBOSE] [DOCSIS.INIT(pid=413)]:  DS-index-11 map to PHY-Rx-14 and HSIF-26
pcd: (265): Starting process mknod (Rule DOCSIS_MKNODSOCIFDRV).
pcd: (265): Starting process insmod (Rule DOCSIS_BRIDGE).
[INFO_VERBOSE] [DOCSIS.INIT(pid=413)]:  DS-index-12 map to PHY-Rx-15 and HSIF-27
[INFO_VERBOSE] [DOCSIS.INIT(pid=413)]:  DS-index-13 map to PHY-Rx-20 and HSIF-28
pcd: (265): Rule DOCSIS_MKNODSOCIFDRV: Success (Process mknod (445)).
pcd: (265): Starting process insmod (Rule DOCSIS_MNG).
[INFO_VERBOSE] [DOCSIS.INIT(pid=413)]:  DS-index-14 map to PHY-Rx-21 and HSIF-29
[INFO_VERBOSE] [DOCSIS.INIT(pid=413)]:  DS-index-15 map to PHY-Rx-22 and HSIF-30
[INFO_VERBOSE] [DOCSIS.INIT(pid=413)]:  DS-index-16 map to PHY-Rx-23 and HSIF-31  Entered docsis_cppi_init

PAL_cppi4Init : domain is 2, cfg ptr is 0x4F053B74
 Entered docsis_cppi_DS_GROUP_init

PAL_cppi4Init : domain is 3, cfg ptr is 0x4F0542E4
 Entered docsis_cppi_DS_GROUP_init

PAL_cppi4Init : domain is 0, cfg ptr is 0x00000000


PAL_cppi4Init : domain is 1, cfg ptr is 0x4F054CD4
pcd: (265): Rule DOCSIS_BRIDGE:
PAL_cppi4Init : domain is 0, cfg ptr is 0x00000000
Success (Process insmod (446)).
pcd: (265): Rule DOCSIS_MNG: Success (Process insmod (447)).
[INFO_VERBOSE] [DOCSIS.INIT(pid=413)]: ------------------ DS Ports Mapping end -----------------------------
[INFO_VERBOSE] [DOCSIS.INIT(pid=413)]: Using MAC address 08:80:39:XX:XX:XX
[INFO] [DOCSIS.INIT(pid=413)]: Using NV IpProvMode 4
[INFO_VERBOSE] [DOCSIS.CHDB_RX(pid=413)]: Docsis module [1] -> rcpIndex [1]
[INFO_VERBOSE] [DOCSIS.CHDB_RX(pid=413)]: Docsis channel ID[1] -> rcpIndex [1]
[INFO_VERBOSE] [DOCSIS.CHDB_RX(pid=413)]: Docsis channel ID[2] -> rcpIndex [2]
[INFO_VERBOSE] [DOCSIS.CHDB_RX(pid=413)]: Docsis channel ID[3] -> rcpIndex [3]
[INFO_VERBOSE] [DOCSIS.CHDB_RX(pid=413)]: Docsis channel ID[4] -> rcpIndex [4]
[INFO_VERBOSE] [DOCSIS.CHDB_RX(pid=413)]: Video channel ID[5] -> rcpIndex [0]
[INFO_VERBOSE] [DOCSIS.CHDB_RX(pid=413)]: Video channel ID[6] -> rcpIndex [0]
[INFO_VERBOSE] [DOCSIS.CHDB_RX(pid=413)]: Video channel ID[7] -> rcpIndex [0]
[INFO_VERBOSE] [DOCSIS.CHDB_RX(pid=413)]: Docsis channel ID[9] -> rcpIndex [5]
[INFO] [DOCSIS.INIT(pid=413)]: Looking for LSDDB /nvram/1/lsddb.ini
[INFO] [DOCSIS.INIT(pid=413)]: Docsis LSDDB: created link from /nvram/1/lsddb.ini to /nvram/3/lsddb.ini
pcd: (265): Starting process mknod (Rule DOCSIS_MKNODMNG).
pcd: (265): Starting process insmod (Rule DOCSIS_KINTR).
pcd: (265): Starting process insmod (Rule DOCSIS_CNI).
pcd: (265): Rule DOCSIS_MKNODMNG: Success (Process mknod (450)).
pcd: (265): Starting process insmod (Rule DOCSIS_FILTERCLASS).
pcd: (265): Rule DOCSIS_KINTR: Success (Process insmod (451)).

PAL_cppi4Init : domain is 0, cfg ptr is 0x00000000
PP Operation TI_PPM_PID_CREATED, pid_handle=6
pcd: (265): Rule DOCSIS_CNI: Success (Process insmod (452)).
pcd: (265): Starting process /usr/sbin/hal_event_mbox (Rule DOCSIS_HALEVENTMBOX).
pcd: (265): Starting process /usr/sbin/hal_cmd_mbox (Rule DOCSIS_HALCMDMBOX).
pcd: (265): Rule DOCSIS_FILTERCLASS: Success (Process insmod (482)).
pcd: (265): Starting process /bin/sh (Rule DOCSIS_FCDEV).
[INFO_VERBOSE] [DOCSIS.HAL(pid=503)]: HAL_EventMbox_Init
pcd: (265): Rule DOCSIS_HALCMDMBOX: Success (Process /usr/sbin/hal_cmd_mbox (504)).
pcd: (265): Rule DOCSIS_HALEVENTMBOX: Success (Process /usr/sbin/hal_event_mbox (503)).
pcd: (265): Starting process /usr/sbin/mlx (Rule DOCSIS_MLX).
[INFO_VERBOSE] [DOCSIS.HAL(pid=503)]: finished successfully
pcd: (265): Rule DOCSIS_MLX: Success (Process /usr/sbin/mlx (512)).
[INFO_VERBOSE] [DOCSIS.HAL(pid=504)]: HAL_CmdMbox_Init
[INFO_VERBOSE] [DOCSIS.HAL(pid=504)]: finished successfully
[INFO_VERBOSE] [DOCSIS.HAL(pid=503)]: HAL_EventMbox_ProcessMain
pcd: (265): Rule DOCSIS_FCDEV: Success (Process /bin/sh (506)).
pcd: (265): Starting process /usr/sbin/hal_tuner_mgr (Rule DOCSIS_HALTUNERMGR).
pcd: (265): Starting process /usr/sbin/dbridge_init (Rule DOCSIS_DBRIDGEINIT).
[INFO_VERBOSE] [DOCSIS.HAL(pid=504)]: HAL_CmdMbox_ProcessMain
[INFO_VERBOSE] [DOCSIS.HAL(pid=504)]: HAL_CmdMbox_ProcessMain started
[INFO_VERBOSE] [DOCSIS.HAL(pid=504)]: Wait for mboxReady
Dbridge Init SUCSESS
Autoconfiguration disabled for lbr0
Autoconfiguration disabled for lan0
Autoconfiguration disabled for wan0
[INFO_VERBOSE] [DOCSIS.HAL(pid=519)]:  HAL_TunerMgrInit
pcd: (265): Rule DOCSIS_HALTUNERMGR: Success (PrAutoconfiguration disabled for cni0
ocess /usr/sbin/hal_tuner_mgr (519)).
[INFO_VERBOSE] [DOCSIS.HAL(pid=519)]: Finished successfully
[INFO_VERBOSE] [DOCSIS.HAL(pid=519)]:  HAL_TunerMgrProcessMain
pcd: (265): Rule DOCSIS_DBRIDGEINIT: Success (Process /usr/sbin/dbridge_init (520)).
pcd: (265): Starting process /bin/sh (Rule DOCSIS_DBRIDGEMDFINIT).
pcd: (265): Starting process /bin/sh (Rule DOCSIS_DBRIDGEL2VPNDSI).
[INFO_VERBOSE] [DOCSIS.DBRIDGE(pid=520)]: The bridge have been configurated successfully
[ERROR] [COMMON_COMPONENTS.LSDDB(pid=520)]: LSDDB - lsddbRt == NULL
pcd: (265): Rule DOCSIS_DBRIDGEMDFINIT: Success (Process /bin/sh (528)).
pcd: (265): Starting process insmod (Rule DOCSIS_PP).
pcd: (265): Rule DOCSIS_DBRIDGEL2VPNDSI: Success (Process /bin/sh (529)).
pcd: (265): Rule DOCSIS_PP: Success (Process insmod (540)).
pcd: (265): Starting process /bin/sh (Rule DOCSIS_PPDEV).
pcd: (265): Starting process /usr/sbin/ledd (Rule DOCSIS_LED).
pcd: (265): Rule DOCSIS_HALREADY: Success.
pcd: (265): Rule DOCSIS_LED: Success (Process /usr/sbin/ledd (543)).
pcd: (265): Starting process /usr/sbin/qos_dsx_sm (Rule DOCSIS_QOSDSXSM).
pcd: (265): Starting process /usr/sbin/dispatcher (Rule DOCSIS_DISPATCHER).
netlink_open: initialized fd 6
[INFO_VERBOSE] [DOCSIS.MDD(pid=545)]: MDD Init completed successfully
pcd: (265): Rule DOCSIS_DISPATCHER: Success (Process /usr/sbin/dispatcher (545)).
pcd: (265): Starting process /usr/sbin/docsis_mac_driver (Rule DOCSIS_MACDRIVER).
pcd: (265): Rule DOCSIS_QOSDSXSM: Success (Process /usr/sbin/qos_dsx_sm (544)).
pcd: (265): Rule DOCSIS_PPDEV: Success (Process /bin/sh (542)).
[INFO_VERBOSE] [DOCSIS.DS(pid=548)]: Number of DS Ports = 16.
[INFO_VERBOSE] [DOCSIS.DS(pid=548)]: Start Global DS Interface Init.
[INFO_VERBOSE] [DOCSIS.HAL_TUNER(pid=519)]: Tuner-Device operations was set to Tuner type 12 - MXL265_TUNER_TYPE
[INFO_VERBOSE] [DOCSIS.HAL_TUNER(pid=519)]: Tuner operations was set to Tuner type 12 - MXL265_TUNER_TYPE
[INFO_VERBOSE] [DOCSIS.HAL(pid=519)]: Registered tuner #0, ID type 12 name MXL265_TUNER_TYPE
[INFO] [DOCSIS.HAL_TUNER(pid=519)]: Device #0 initialization (HAL_mxlHrclsDeviceGlobalInitSrv) Start
[INFO_VERBOSE] [DOCSIS.HAL_TUNER(pid=519)]: MXL265_TUNER_TYPE [devId = 0] [i2c_address = 0x50] [status = 0]
[INFO_VERBOSE] [DOCSIS.HAL_TUNER(pid=519)]: MXL265_TUNER_TYPE [ID=0] : ChipId = 0x1, Version = 0x1
[INFO_VERBOSE] [DOCSIS.HAL_TUNER(pid=519)]: MXL265_TUNER_TYPE [ID=0] : Driver version = 3.1.2.2.RC-7
[INFO_VERBOSE] [DOCSIS.HAL_TUNER(pid=519)]: MXL265_TUNER_TYPE [ID=0] : Firmware version = 0.0.0.0.RC-0
[INFO_VERBOSE] [DOCSIS.HAL_TUNER(pid=519)]: MXL265_TUNER_TYPE [ID=0] : Boot loader version = 2.0.0.2.RC-0
[INFO_VERBOSE] [DOCSIS.HAL_TUNER(pid=519)]: After MxLWare267_API_ConfigDevice
[INFO_VERBOSE] [DOCSIS.HAL_TUNER(pid=519)]: MXL265_TUNER_TYPE Firmware Download completed successfully [FW size 52797] [Time 5.5 sec] [ID=0]
[INFO_VERBOSE] [DOCSIS.HAL_TUNER(pid=519)]: MXL265_TUNER_TYPE [ID=0] : ChipId = 0x1, Version = 0x1
[INFO_VERBOSE] [DOCSIS.HAL_TUNER(pid=519)]: MXL265_TUNER_TYPE [ID=0] : Driver version = 3.1.2.2.RC-7
[INFO_VERBOSE] [DOCSIS.HAL_TUNER(pid=519)]: MXL265_TUNER_TYPE [ID=0] : Firmware version = 3.1.2.2.RC-12
[INFO_VERBOSE] [DOCSIS.HAL_TUNER(pid=519)]: MXL265_TUNER_TYPE [ID=0] : Boot loader version = 2.0.0.2.RC-0
[INFO] [DOCSIS.HAL_TUNER(pid=519)]: ****** MxL Tuner device #0 initialization SUCCESS ********
[ERROR] [DOCSIS.HAL_TUNER(pid=519)]: [HRCLS] FB tuner was already enabled
[INFO] [DOCSIS.HAL_TUNER(pid=519)]: MXL265_TUNER_TYPE Tuner-WaitLock (ID=0) starts with Timeout-Limit to 5000 mSec
[INFO] [DOCSIS.HAL_TUNER(pid=519)]: MXL265_TUNER_TYPE Tuner-WaitLock (ID=0) took 130 mSec
[INFO] [DOCSIS.HAL_TUNER(pid=519)]:  **** MxL Tuner Configuration done successfully ****
[INFO] [DOCSIS.HAL_PHY(pid=548)]:  Release SerDes lane 0 From Reset so that lane 1 will lock
[INFO] [DOCSIS.HAL_PHY(pid=548)]: HSIF lane[0] released from reset - ok [Reg 0x1e44 = 0x5481]
[INFO] [DOCSIS.HAL_PHY(pid=548)]: HSIF lane[1] released from reset - ok [Reg 0x1e45 = 0x5481]
[INFO] [DOCSIS.HAL_PHY(pid=548)]: HSIF lane 1 Init done ok [disable_tx_loops=0   SerDes_lock_loops=0   power_up_SerDes_loops=0]
[INFO] [DOCSIS.HAL_PHY(pid=548)]: HSIF Init done ok [counters_loops=0   sync_lock_loops=0 ]
[INFO_VERBOSE] [DOCSIS.HAL_TUNER(pid=519)]:  ********* MXL265_TUNER_TYPE deviceId 0 US SerDes Sync is lock [syncLostCnt=0 loop=0]
[INFO] [DOCSIS.HAL(pid=548)]: *** HAL_TunerInitUSHsif Success
[INFO_VERBOSE] [DOCSIS.HAL(pid=548)]:  HAL_MacDsMacInit done.
[INFO_VERBOSE] [DOCSIS.HAL(pid=548)]:  HAL_MacDsCopInit done.
[INFO_VERBOSE] [DOCSIS.HAL(pid=548)]:  MAC DS Init completed successfully.
[INFO_VERBOSE] [DOCSIS.HAL(pid=548)]: HAL_MacMapperOutOfReset start.
[INFO_VERBOSE] [DOCSIS.HAL(pid=548)]: HAL_SyncInit Done.
[INFO_VERBOSE] [DOCSIS.HAL(pid=548)]:  Found entry index 0 in HW Unicast filter table.
[INFO_VERBOSE] [DOCSIS.DS(pid=548)]: Global DS Interface Init Done.
[INFO_VERBOSE] [DOCSIS.DS(pid=548)]: Creating DSM process for DS port number 24.
[INFO_VERBOSE] [DOCSIS.DS(pid=548)]: Creating DSM process for DS port number 23.
pcd: (265): Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR24).
[INFO_VERBOSE] [DOCSIS.DS(pid=548)]: Creating DSM process for DS port number 22.
pcd: (265): Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR23).
[INFO_VERBOSE] [DOCSIS.DS(pid=548)]: Creating DSM process for DS port number 21.
pcd: (265): Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR22).
pcd: (265): Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR21).
pcd: (265): Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR16).
[INFO_VERBOSE] [DOCSIS.DS(pid=548)]: Creating DSM process for DS port number 16.
pcd: (265): Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR15).
[INFO_VERBOSE] [DOCSIS.DS(pid=548)]: Creating DSM process for DS port number 15.
pcd: (265): Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR14).
pcd: (265): Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR13).
[INFO_VERBOSE] [DOCSIS.DS(pid=548)]: Creating DSM process for DS port number 14.
pcd: (265): Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR12).
pcd: (265): Rule DOCSIS_DSMNGR24: Success (Process /usr/sbin/downstream_manager (558)).
pcd: (265): Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR11).
pcd: (265): Rule DOCSIS_DSMNGR23: Success (Process /usr/sbin/downstream_manager (559)).
pcd: (265): Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR10).
pcd: (265): Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR9).
pcd: (265): Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR4).
pcd: (265): Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR3).
pcd: (265): Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR2).
pcd: (265): Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR1).
pcd: (265): Rule DOCSIS_DSMNGR22: Success (Process /usr/sbin/downstream_manager (560)).
pcd: (265): Rule DOCSIS_DSMNGR21: Success (Process /usr/sbin/downstream_manager (561)).
pcd: (265): Rule DOCSIS_DSMNGR16: Success (Process /usr/sbin/downstream_manager (562)).
[INFO_VERBOSE] [DOCSIS.DS(pid=548)]: Creating DSM process for DS port number 13.
[INFO_VERBOSE] [DOCSIS.DS(pid=548)]: Creating DSM process for DS port number 12.
pcd: (265): Rule DOCSIS_DSMNGR15: Success (Process /usr/sbin/downstream_manager (563)).
[INFO_VERBOSE] [DOCSIS.DS(pid=548)]: Creating DSM process for DS port number 11.
[INFO_VERBOSE] [DOCSIS.DS(pid=559)]: Run DS Manager 23.
[INFO_VERBOSE] [DOCSIS.DS(pid=558)]: Run DS Manager 24.
pcd: (265): Rule DOCSIS_DSMNGR14: Success (Process /usr/sbin/downstream_manager (564)).
pcd: (265): Rule DOCSIS_DSMNGR13: Success (Process /usr/sbin/downstream_manager (565)).
pcd: (265): Rule DOCSIS_DSMNGR12: Success (Process /usr/sbin/downstream_manager (566)).
pcd: (265): Rule DOCSIS_DSMNGR11: Success (Process /usr/sbin/downstream_manager (567)).
pcd: (265): Rule DOCSIS_DSMNGR3: Success (Process /usr/sbin/downstream_manager (571)).
pcd: (265): Rule DOCSIS_DSMNGR10: Success (Process /usr/sbin/downstream_manager (568)).
pcd: (265): Rule DOCSIS_DSMNGR4: Success (Process /usr/sbin/downstream_manager (570)).
pcd: (265): Rule DOCSIS_DSMNGR9: Success (Process /usr/sbin/downstream_manager (569)).
pcd: (265): Rule DOCSIS_DSMNGR2: Success (Process /usr/sbin/downstream_manager (572)).
pcd: (265): Rule DOCSIS_DSMNGR1: Success (Process /usr/sbin/downstream_manager (573)).
[INFO_VERBOSE] [DOCSIS.DS(pid=558)]: DsChannelPortID --------> 24.
[INFO_VERBOSE] [DOCSIS.DS(pid=559)]: DsChannelPortID --------> 23.
[INFO_VERBOSE] [DOCSIS.DS(pid=559)]: DSM ContextOwner -------> 27.
[INFO_VERBOSE] [DOCSIS.DS(pid=558)]: DSM ContextOwner -------> 28.
[INFO_VERBOSE] [DOCSIS.DS(pid=560)]: Run DS Manager 22.
[INFO_VERBOSE] [DOCSIS.DS(pid=561)]: Run DS Manager 21.
[INFO_VERBOSE] [DOCSIS.DS(pid=562)]: Run DS Manager 16.
[INFO_VERBOSE] [DOCSIS.DS(pid=560)]: DsChannelPortID --------> 22.
[INFO_VERBOSE] [DOCSIS.DS(pid=560)]: DSM ContextOwner -------> 26.
[INFO_VERBOSE] [DOCSIS.DS(pid=558)]: Start HAL_GlobalRegistration.
[INFO_VERBOSE] [DOCSIS.DS(pid=561)]: DsChannelPortID --------> 21.
[INFO_VERBOSE] [DOCSIS.DS(pid=559)]: Start HAL_GlobalRegistration.
[INFO_VERBOSE] [DOCSIS.DS(pid=562)]: DsChannelPortID --------> 16.
[INFO_VERBOSE] [DOCSIS.DS(pid=561)]: DSM ContextOwner -------> 25.
[INFO_VERBOSE] [DOCSIS.DS(pid=562)]: DSM ContextOwner -------> 20.
[INFO_VERBOSE] [DOCSIS.DS(pid=560)]: Start HAL_GlobalRegistration.
[INFO_VERBOSE] [DOCSIS.DS(pid=561)]: Start HAL_GlobalRegistration.
[INFO_VERBOSE] [DOCSIS.DS(pid=548)]: Creating DSM process for DS port number 10.
[INFO_VERBOSE] [DOCSIS.DS(pid=558)]:  Init DS channel HW for port ID 24.
[INFO_VERBOSE] [DOCSIS.DS(pid=559)]:  Init DS channel HW for port ID 23.
[INFO_VERBOSE] [DOCSIS.HAL(pid=559)]: calling HAL_MacDsChannelEnable
[INFO_VERBOSE] [DOCSIS.DS(pid=548)]: Creating DSM process for DS port number 9.
[INFO_VERBOSE] [DOCSIS.HAL(pid=558)]: calling HAL_MacDsChannelEnable
[INFO_VERBOSE] [DOCSIS.HAL(pid=558)]: MAC DS channel 23 Enable completed successfully.
[INFO_VERBOSE] [DOCSIS.HAL(pid=559)]: MAC DS channel 22 Enable completed successfully.
[INFO_VERBOSE] [DOCSIS.DS(pid=548)]: Creating DSM process for DS port number 4.
[INFO_VERBOSE] [DOCSIS.DS(pid=548)]: Creating DSM process for DS port number 3.
[INFO_VERBOSE] [DOCSIS.DS(pid=562)]: Start HAL_GlobalRegistration.
[INFO_VERBOSE] [DOCSIS.DS(pid=548)]: Creating DSM process for DS port number 2.
[INFO_VERBOSE] [DOCSIS.DS(pid=548)]: Creating DSM process for DS port number 1.
[INFO_VERBOSE] [DOCSIS.DS(pid=560)]:  Init DS channel HW for port ID 22.
[INFO_VERBOSE] [DOCSIS.DS(pid=561)]:  Init DS channel HW for port ID 21.
[INFO_VERBOSE] [DOCSIS.HAL(pid=560)]: calling HAL_MacDsChannelEnable
[INFO_VERBOSE] [DOCSIS.HAL(pid=560)]: MAC DS channel 21 Enable completed successfully.
[INFO_VERBOSE] [DOCSIS.HAL(pid=561)]: calling HAL_MacDsChannelEnable
[INFO_VERBOSE] [DOCSIS.HAL(pid=561)]: MAC DS channel 20 Enable completed successfully.
[INFO_VERBOSE] [DOCSIS.DS(pid=562)]:  Init DS channel HW for port ID 16.
[INFO_VERBOSE] [DOCSIS.HAL(pid=562)]: calling HAL_MacDsChannelEnable
[INFO_VERBOSE] [DOCSIS.HAL(pid=562)]: MAC DS channel 15 Enable completed successfully.
[INFO_VERBOSE] [DOCSIS.DS(pid=563)]: Run DS Manager 15.
[INFO_VERBOSE] [DOCSIS.DS(pid=563)]: DsChannelPortID --------> 15.
[INFO_VERBOSE] [DOCSIS.DS(pid=563)]: DSM ContextOwner -------> 19.
[INFO_VERBOSE] [DOCSIS.DS(pid=563)]: Start HAL_GlobalRegistration.
[INFO_VERBOSE] [DOCSIS.DS(pid=563)]:  Init DS channel HW for port ID 15.
[INFO_VERBOSE] [DOCSIS.HAL(pid=563)]: calling HAL_MacDsChannelEnable
[INFO_VERBOSE] [DOCSIS.HAL(pid=563)]: MAC DS channel 14 Enable completed successfully.
[INFO_VERBOSE] [DOCSIS.DS(pid=565)]: Run DS Manager 13.
[INFO_VERBOSE] [DOCSIS.DS(pid=564)]: Run DS Manager 14.
[INFO_VERBOSE] [DOCSIS.DS(pid=564)]: DsChannelPortID --------> 14.
[INFO_VERBOSE] [DOCSIS.DS(pid=564)]: DSM ContextOwner -------> 18.
[INFO_VERBOSE] [DOCSIS.DS(pid=565)]: DsChannelPortID --------> 13.
[INFO_VERBOSE] [DOCSIS.DS(pid=565)]: DSM ContextOwner -------> 17.
[INFO_VERBOSE] [DOCSIS.DS(pid=564)]: Start HAL_GlobalRegistration.
[INFO_VERBOSE] [DOCSIS.DS(pid=565)]: Start HAL_GlobalRegistration.
[INFO_VERBOSE] [DOCSIS.DS(pid=564)]:  Init DS channel HW for port ID 14.
[INFO_VERBOSE] [DOCSIS.DS(pid=565)]:  Init DS channel HW for port ID 13.
[INFO_VERBOSE] [DOCSIS.HAL(pid=564)]: calling HAL_MacDsChannelEnable
[INFO_VERBOSE] [DOCSIS.HAL(pid=564)]: MAC DS channel 13 Enable completed successfully.
[INFO_VERBOSE] [DOCSIS.HAL(pid=565)]: calling HAL_MacDsChannelEnable
[INFO_VERBOSE] [DOCSIS.HAL(pid=565)]: MAC DS channel 12 Enable completed successfully.
[INFO_VERBOSE] [DOCSIS.DS(pid=566)]: Run DS Manager 12.
[INFO_VERBOSE] [DOCSIS.DS(pid=566)]: DsChannelPortID --------> 12.
[INFO_VERBOSE] [DOCSIS.DS(pid=566)]: DSM ContextOwner -------> 16.
[INFO_VERBOSE] [DOCSIS.DS(pid=570)]: Run DS Manager 4.
[INFO_VERBOSE] [DOCSIS.DS(pid=568)]: Run DS Manager 10.
[INFO_VERBOSE] [DOCSIS.DS(pid=567)]: Run DS Manager 11.
[INFO_VERBOSE] [DOCSIS.DS(pid=569)]: Run DS Manager 9.
[INFO_VERBOSE] [DOCSIS.DS(pid=573)]: Run DS Manager 1.
[INFO_VERBOSE] [DOCSIS.DS(pid=571)]: Run DS Manager 3.
[INFO_VERBOSE] [DOCSIS.DS(pid=568)]: DsChannelPortID --------> 10.
[INFO_VERBOSE] [DOCSIS.DS(pid=567)]: DsChannelPortID --------> 11.
[INFO_VERBOSE] [DOCSIS.DS(pid=569)]: DsChannelPortID --------> 9.
[INFO_VERBOSE] [DOCSIS.DS(pid=570)]: DsChannelPortID --------> 4.
[INFO_VERBOSE] [DOCSIS.DS(pid=572)]: Run DS Manager 2.
[INFO_VERBOSE] [DOCSIS.DS(pid=572)]: DsChannelPortID --------> 2.
[INFO_VERBOSE] [DOCSIS.DS(pid=572)]: DSM ContextOwner -------> 6.
[INFO_VERBOSE] [DOCSIS.DS(pid=570)]: DSM ContextOwner -------> 8.
[INFO_VERBOSE] [DOCSIS.DS(pid=568)]: DSM ContextOwner -------> 14.
[INFO_VERBOSE] [DOCSIS.DS(pid=571)]: DsChannelPortID --------> 3.
[INFO_VERBOSE] [DOCSIS.DS(pid=571)]: DSM ContextOwner -------> 7.
[INFO_VERBOSE] [DOCSIS.DS(pid=567)]: DSM ContextOwner -------> 15.
[INFO_VERBOSE] [DOCSIS.DS(pid=569)]: DSM ContextOwner -------> 13.
[INFO_VERBOSE] [DOCSIS.DS(pid=573)]: DsChannelPortID --------> 1.
[INFO_VERBOSE] [DOCSIS.DS(pid=573)]: DSM ContextOwner -------> 5.
[INFO_VERBOSE] [DOCSIS.DS(pid=566)]: Start HAL_GlobalRegistration.
[INFO_VERBOSE] [DOCSIS.DS(pid=568)]: Start HAL_GlobalRegistration.
[INFO_VERBOSE] [DOCSIS.DS(pid=567)]: Start HAL_GlobalRegistration.
[INFO_VERBOSE] [DOCSIS.DS(pid=571)]: Start HAL_GlobalRegistration.
[INFO_VERBOSE] [DOCSIS.DS(pid=572)]: Start HAL_GlobalRegistration.
[INFO_VERBOSE] [DOCSIS.DS(pid=570)]: Start HAL_GlobalRegistration.
[INFO_VERBOSE] [DOCSIS.DS(pid=569)]: Start HAL_GlobalRegistration.
[INFO_VERBOSE] [DOCSIS.DS(pid=573)]: Start HAL_GlobalRegistration.
[INFO_VERBOSE] [DOCSIS.DS(pid=566)]:  Init DS channel HW for port ID 12.
[INFO_VERBOSE] [DOCSIS.HAL(pid=566)]: calling HAL_MacDsChannelEnable
[INFO_VERBOSE] [DOCSIS.DS(pid=571)]:  Init DS channel HW for port ID 3.
[INFO_VERBOSE] [DOCSIS.DS(pid=567)]:  Init DS channel HW for port ID 11.
[INFO_VERBOSE] [DOCSIS.DS(pid=568)]:  Init DS channel HW for port ID 10.
[INFO_VERBOSE] [DOCSIS.HAL(pid=566)]: MAC DS channel 11 Enable completed successfully.
[INFO_VERBOSE] [DOCSIS.HAL(pid=568)]: calling HAL_MacDsChannelEnable
[INFO_VERBOSE] [DOCSIS.DS(pid=572)]:  Init DS channel HW for port ID 2.
[INFO_VERBOSE] [DOCSIS.HAL(pid=568)]: MAC DS channel 9 Enable completed successfully.
[INFO_VERBOSE] [DOCSIS.US(pid=548)]: usPortsNumber = 4
[INFO_VERBOSE] [DOCSIS.HAL(pid=548)]:  Entered UsFwDownload
[INFO_VERBOSE] [DOCSIS.HAL(pid=548)]:  change Arm state to reset
[INFO_VERBOSE] [DOCSIS.HAL(pid=548)]:  Load instruction file /usr/sbin/FwUpstreamDocsis2_I.bin to 0x1600000
[INFO_VERBOSE] [DOCSIS.HAL(pid=548)]:  Load data file /usr/sbin/FwUpstreamDocsis2_D.bin to 0x1620000
[INFO_VERBOSE] [DOCSIS.HAL(pid=548)]:  Configure ARM to Host interrupts
[INFO_VERBOSE] [DOCSIS.HAL(pid=548)]:  change Arm state to out of reset
[INFO_VERBOSE] [DOCSIS.HAL(pid=512)]:  initialize mboxReadyIccContext
[INFO_VERBOSE] [DOCSIS.HAL(pid=512)]:  HAL_CmdMbox_SendMboxReady - initialize eventMboxIccContext
[INFO_VERBOSE] [DOCSIS.HAL(pid=512)]:  ICC_send_message
[INFO_VERBOSE] [DOCSIS.HAL(pid=512)]:  ICC_send_message
[INFO_VERBOSE] [DOCSIS.HAL(pid=504)]: MboxReady received
[INFO_VERBOSE] [DOCSIS.HAL(pid=503)]: HAL_EventMbox_ProcessMain - Initialized Mbox Address
[INFO_VERBOSE] [DOCSIS.HAL(pid=504)]: MboxControl Addrepcd: (265): Starting process /usr/sbin/upstream_manager (Rule DOCSIS_USMNGR1).
ss (FW) - 0x340dc00
pcd: (265): Starting process /usr/sbin/upstream_manager (Rule DOCSIS_USMNGR2).
pcd: (265): Starting process /usr/sbin/upstream_manager (Rule DOCSIS_USMNGR3).
pcd: (265): Starting process /usr/sbin/upstream_manager (Rule DOCSIS_USMNGR4).
[INFO_VERBOSE] [DOCSIS.HAL(pid=504)]: MboxControl Address (HOST) - 0x240dc00
[INFO_VERBOSE] [DOCSIS.HAL(pid=504)]: CmdMbox Address(FW) - 0x340dc0c
[INFO_VERBOSE] [DOCSIS.HAL(pid=504)]: CmdMbox Address(HOST) - 0x240dc0c
[INFO] [DOCSIS.HAL(pid=548)]:  PGA enable. AMP_OFF - Normal
pcd: (265): Rule DOCSIS_USMNGR1: Success (Process /usr/sbin/upstream_manager (574)).
pcd: (265): Rule DOCSIS_USMNGR3: Success (Process /usr/sbin/upstream_manager (576)).
pcd: (265): Rule DOCSIS_USMNGR4: Success (Process /usr/sbin/upstream_manager (577)).
pcd: (265): Rule DOCSIS_USMNGR2: Success (Process /usr/sbin/upstream_manager (575)).
pcd: (265): Rule DOCSIS_MACDRIVER: Success (Process /usr/sbin/docsis_mac_driver (548)).
pcd: (265): Starting process /usr/sbin/snmp_agent_cm (Rule DOCSIS_SNMPAGENT).
pcd: (265): Starting process /usr/sbin/bpi_auth (Rule DOCSIS_BPIAUTH).
pcd: (265): Rule DOCSIS_BPIAUTH: Success (Process /usr/sbin/bpi_auth (579)).
pcd: (265): Starting process /usr/sbin/bpi_tek (Rule DOCSIS_BPITEK).
pcd: (265): Starting process /usr/sbin/bpi_sa_map (Rule DOCSIS_BPISAMAP).
pcd: (265): Rule DOCSIS_BPISAMAP: Success (Process /usr/sbin/bpi_sa_map (581)).
pcd: (265): Rule DOCSIS_BPITEK: Success (Process /usr/sbin/bpi_tek (580)).
SNMPA_CreateSocketEntry : type 0, addr = 0, port = 0, ifname = /var/tmp/cm_snmp_ctrl List = (nil)
Cntl Entry created
[INFO_VERBOSE] [DOCSIS.UTILS(pid=578)]: Uboot Env ver read: U-Boot 1.2.0-g1a0473cf-dirty (May  3 2013 - 08:43:46) Cisco-Boot 3.4.19
[INFO_VERBOSE] [DOCSIS.UTILS(pid=578)]: Uboot version = 3.4.19
pcd: (265): Rule DOCSIS_SNMPAGENT: Success (Process /usr/sbin/snmp_agent_cm (578)).
SNMPA_CreateSocketEntry : type 1, addr = c0a86401, port = 161, ifname = lan0 List = 0x73038
SNMPA_CreateSocketEntry : type 1, addr = c0a86401, port = 162, ifname = lan0 List = 0x73038
SNMPA_CreateSocketEntry : type 1, addr = a000001, port = 161, ifname = brlan0 List = 0x73038
Can't bind SNMP server socket
SNMPA_CreateSocketEntry : type 1, addr = a000001, port = 162, ifname = brlan0 List = 0x73038
Can't bind SNMP server socket
pcd: (265): Starting process /usr/sbin/eventmgr_cm (Rule DOCSIS_EVENTMNGR).
[INFO] [COMMON_COMPONENTS.EVENT_MNGR(pid=604)]: Control socket created successfully
[INIT] [COMMON_COMPONENTS.EVENT_MNGR(pid=604)]: Init successfully
[INFO] [COMMON_COMPONENTS.EVENT_MNGR(pid=604)]: Opening SNMP service
[INFO] [COMMON_COMPONENTS.EVENT_MNGR(pid=604)]: Starting main loop
pcd: (265): Rule DOCSIS_EVENTMNGR: Success (Process /usr/sbin/eventmgr_cm (604)).
pcd: (265): Starting process /usr/sbin/docsis_mac_manager (Rule DOCSIS_MACMANAGER).
[INFO_VERBOSE] [COMMON_COMPONENTS.GIM(pid=605)]: nid=4107: type SRN with 0 bytes data
Loading erouter0 network interface driver
[INFO] [GW.PROV(pid=294)]: GW - Got DOCSIS Initialized
eRouter: Network interface initialized successfully
Autoconfiguration disabled for esafe0
eRouter: Network interface registered successfully
Getting Factory Mode = 0
[INFO] [DOCSIS.ESAFE(pid=294)]: Init ESAFE dev: 1 - erouter0, RngholdoffMask 0x00000002, DHCP str EROUTER, MAC Address 08:80:39:XX:XX:XX
[INFO] [DOCSIS.DBRIDGE(pid=294)]: Connect DOCSIS local bridge : Disconnect, lsdActive 0
pcd: (265): Rule DOCSIS_MACMANAGER: Success (Process /usr/sbin/docsis_mac_manager (605)).
[INFO] [DOCSIS.DMG(pid=605)]: eRouter exists, not connecting Local bridge from DMG
pcd: (265): Starting process /usr/sbin/cpu_report (Rule DOCSIS_CPUREPORT).
pcd: (265): Rule DOCSIS_CPUREPORT: Success (Process /usr/sbin/cpu_report (626)).
pcd: (265): Rule DOCSIS_LASTRULE: Success.
pcd: (265): Starting process /etc/utopia/service.d/service_cosa.sh (Rule GW_CCSP).
pcd: (265): Starting process insmod (Rule VFE_IPTV_BRIDGE).
pcd: (265): Starting process insmod (Rule PACM_MTANI).
pcd: (265): Starting process /usr/sbin/consolesecurity (Rule DOCSIS_CONSOLESECURITY).
pcd: (265): Starting process /usr/sbin/telnetd (Rule SYSTEM_TELNET).
pcd: (265): Starting process /usr/sbin/dropbear (Rule SYSTEM_SSHD).
pcd: (265): Rule SYSTEM_SSHD: Success (Process /usr/sbin/dropbear (632)).
pcd: (265): Rule SYSTEM_TELNET: Success (Process /usr/sbin/telnetd (631)).
mtani: Network interface initialized successfully

IPTV Bridge char device init done
Autoconfiguration disabled for esafe1
mtani: Network interface registered successfully
pcd: (265): Rule VFE_IPTV_BRIDGE: Success (Process insmod (628)).
pcd: (265): Starting process /bin/sh (Rule VFE_IPTV_BRIDGE_DEV).
pcd: (265): Rule PACM_MTANI: Success (Process insmod (629)).
pcd: (265): Starting process /usr/sbin/pacm_init (Rule PACM_INIT).
[632] Jan 01 00:01:10 Failed reading '/etc/dropbear/dropbear_dss_host_key', disabling DSS
[632] Jan 01 00:01:10 Not backgrounding
killall: crond: no process killed
pcd: (265): Rule VFE_IPTV_BRIDGE_DEV: Success (Process /bin/sh (655)).
pcd: (265): Starting process /usr/sbin/vfe_mgr_app (Rule VFE_VMA).
Autoconfiguration disabled for mta0
Production config saved to NVRAMSTA MAC initialized to 08:80:39:XX:XX:EEPACM - Exec PACM_Prov_DbInit
PACM - Exec PACM_MSM_DbInit
PACM - Exec Security_InitDataBase
PACM - Exec SnmpDB_Init
PACM - Exec M5T_Prov_DbInit
M5T_Prov_DbInit Exit
pcd: (265): Rule PACM_INIT: Success (Process /usr/sbin/pacm_init (656)).
pcd: (265): Starting process insmod (Rule VOICE_INSMXPMOD).
pcd: (265): Starting process /usr/sbin/pacm_vendor_app (Rule PACM_VENDORAPP).
pcd: (265): Starting process /usr/sbin/pacm_snmp_agent (Rule PACM_SNMP).
pcd: (265): Starting process /usr/sbin/pacm_security (Rule PACM_SECURITY).
pcd: (265): Starting process /usr/sbin/pacm_event_mgr (Rule PACM_EVENTMGR).
pcd: (265): Starting process /usr/sbin/pacm_doim (Rule PACM_DOIM).
Starting Config Recover Daemon ...
[INFO] [PACM.PROVISION(pid=656)]: Initializing Privisioning Database
[INFO] [PACM.PROVISION(pid=656)]: PACM_Prov_DbDefaultSet: entry point mask = 02
[INFO] [PACM.PROVISION(pid=656)]: set default opt 122
pcd: (265): Rule VFE_VMA: Success (Process /usr/sbin/vfe_mgr_app (684)).
[INFO] [PACM.MTA_CONTROL(pid=656)]: Initializing MSM Database
pcd: (265): Rule VFE_LASTRULE: Success.
[INFO] [PACM.SECURITY(pid=656)]: Security_InitDataBase succeeded data address 4624e28
[INFO] [VFE.VMA(pid=684)]: VMA is working with PCD
pcd: (265): Rule PACM_DOIM: Success (Process /usr/sbin/pacm_doim (693)).
pcd: (265): Rule PACM_EVENTMGR: Success (Process /usr/sbin/pacm_event_mgr (692)).
Warning: TIMER1 may already be in use
MXP_TMR: Calibrating MXP Timer...   Ticks/sec=200
Starting MXP timer
[INFO] [VFE.VMA(pid=684)]: VMA ICC init successfullyMXP module loaded

pcd: (265): Rule VOICE_INSMXPMOD: Success (Process insmod (688)).
[INFO] [VFE.VMA(pid=684)]: VMA INIT OK....
pcd: (265): Starting process insmod (Rule VOICE_INSMXPMEM).
[INFO] [VFE.VMA(pid=684)]: Initialized successfully+++ irwChoice = 2

[INFO] [PACM.EV_MGR(pid=692)]: Success initialize enterprise number
[INFO] [PACM.EV_MGR(pid=692)]: Success initialize vendor ID: TI
[INFO] [PACM.EV_MGR(pid=692)]: Success initialize vendor event table
[INFO] [PACM.DOIM(pid=693)]: Start DOIM proc
[INFO] [PACM.DOIM(pid=693)]: DOIM start runningMXP memory module loaded

sh: write error: Bad address
pcd: (265): Rule PACM_VENDORAPP: Success (Process /usr/sbin/pacm_vendor_app (689)).
pcd: (265): Rule VOICE_INSMXPMEM: Success (Process insmod (718)).
pcd: (265): Starting process insmod (Rule VOICE_INSDSPMOD).
pcd: (265): Rule DOCSIS_CONSOLESECURITY: Success (Process /usr/sbin/consolesecurity (630)).
82: Disabling  PUMA DSPSS
85: Taking PUMA DSPSS IN  RESET
[INFO] [PACM.DOIM(pid=693)]: DoIM was initiated succesfully
[INFO] [COMMON_COMPONENTS.EVENT_MNGR(pid=692)]: Control socket created successfully
Elected subsystem is eRT.
./CcspCrSsp -subsys eRT.
[INIT] [COMMON_COMPONENTS.EVENT_MNGR(pid=692)]: Init successfullyHW_DSP module loaded

pcd: (265): Rule VOICE_INSDSPMOD: Success (Process insmod (730)).
pcd: (265): Starting process insmod (Rule VOICE_INSTELEHAL).
[INFO] [COMMON_COMPONENTS.EVENT_MNGR(pid=692)]: Starting main loop
Processing configuration file...
Found command: sysdescr	eMTA SNMP Agent
Found command: syscontact     Cisco
Found command: sysLocation    5030 Sugarloaf Parkway, Lawrenceville, GA 30044
Found command: read-community	public
Found command: write-community	private
Found command: trap-community	SNMP-trap
Found command: nv-file     /etc/snmp_mta_nv.txt
Hit EOF of config file
[INFO] [PACM.VENDOR_APP(pid=689)]: Starting vendor application main loop
[INFO] [PACM.SNMP(pid=690)]: Finished to init eSafe
[INFO] [PACM.SECURITY(pid=691)]: Start Security Manager


****HOST INFORMATION****
sysDescr is "eMTA SNMP Agent"
sysContact is "Cisco"
sysLocation is "5030 Sugarloaf Parkway, Lawrenceville, GA 30044"
System Boot time was Thu Jan  1 00:01:17 1970
System object identifier has 14 components:
	0.0.0.0.0.0.0.0.0.0.0.0.0.0.


****SNMP AGENT INFORMATION****
Community names:
	Read: 	public
	Write:	private
	Trap: 	SNMP-trap
 	 nv-file: /etc/snmp_mta_nv.txt


SNMPA_CreateSocketEntry : type 0, addr = 0, port = 0, ifname = /var/tmp/mta_snmp_ctrl List = (nil)
Cntl Entry created
TIUHAL: Finished TDM configuration
TIUHAL using DOCSIS clock source
pcd: (265): Rule PACM_SECURITY: Success (Process /usr/sbin/pacm_security (691)).
pcd: (265): Rule VOICE_INSTELEHAL: Success (Process insmod (741)).
pcd: (265): Starting process udevstart (Rule VOICE_UDEVSTART).
[INFO] [PACM.SECURITY(pid=691)]: Security_StateMachineInit
[INFO] [PACM.SECURITY(pid=691)]: Security CLI redirected to console
[INFO] [PACM.SNMP(pid=690)]: Setting engine ID to 0000118b03088039e801ee01
[INFO] [PACM.SECURITY(pid=691)]: Allocated tickets (FLASH storage is  enabled)
pcd: (265): Rule VOICE_UDEVSTART: Success (Process udevstart (756)).
pcd: (265): Starting process /usr/sbin/M5tPc20Edva (Rule VOICE_GGAPP).
[ERROR] [PACM.SECURITY(pid=691)]: Failed to get tickets from FLASH, using local
[INFO] [PACM.SECURITY(pid=691)]: Ticket store initialized current version 986bd320
[INFO] [PACM.SECURITY(pid=691)]: Init Km Realms
[INFO] [PACM.SECURITY(pid=691)]: Created ICC dest point
[INFO] [PACM.SECURITY(pid=691)]: Realm DB Init
[INFO] [PACM.SECURITY(pid=691)]: Init SecProvdata
[INFO] [PACM.SECURITY(pid=691)]: Resetting Prov Serv Data
[INFO] [PACM.SECURITY(pid=691)]: InvalidateFlashTickets from NV: 0
[INFO] [PACM.SECURITY(pid=691)]: Init Km Realms
[INFO] [PACM.SECURITY(pid=691)]: Reset certs, location: /nvram/2/certificates
./CcspPandMSsp -subsys eRT.
main -- 227main -- create file finished.
[INFO] [PACM.SECURITY(pid=691)]: Certs in nvram ok
[INFO] [PACM.SECURITY(pid=691)]: Spawn all Security threads
[WARNING] [PACM.SECURITY(pid=691)]: Socket Manager not created
[INFO] [PACM.SECURITY(pid=691)]: Succesfully got IPC socket 5
[INFO] [PACM.SECURITY(pid=691)]: DHDb manager created
pcd: (265): Rule PACM_SNMP: Success (Process /usr/sbin/pacm_snmp_agent (690)).
[INFO_VERBOSE] [DOCSIS.UTILS(pid=690)]: Uboot Env ver read: U-Boot 1.2.0-g1a0473cf-dirty (May  3 2013 - 08:43:46) Cisco-Boot 3.4.19
[INFO_VERBOSE] [DOCSIS.UTILS(pid=690)]: Uboot version = 3.4.19
[INFO] [PACM.SECURITY(pid=691)]: DH DB manager runs
[INFO] [PACM.VOIM(pid=691)]: VoIM was initiated succesfully with ID 2062
[INFO] [PACM.SECURITY(pid=691)]: SecurityManager start....
[INFO] [PACM.SECURITY(pid=691)]: Security Manager going to wait for icc messages
[INFO] [PACM.VOIM(pid=690)]: VoIM was initiated succesfully with ID 2055
tcb_alloc: task id=1,name=mxproot,busy=1
tcb_alloc: task id=2,name=XSPY,busy=1
Initializing signal_handler
tcb_alloc: task id=3,name=XTELNET,busy=1
tcb_alloc: task id=4,name=ROOT,busy=1
>>>> rootInit <<<<<
Creating Golden Gateway application...
##### vim_query_perm_memory - total_tcids = 9
Registered with TIUHAL version 3
[ERROR] [VOICE.XSPY(pid=764)]: 0000002349 - UTILS: MAS SLIC WB Mode Support Valid value in nvram, 0
TID(M) 0 tcb_alloc: task id=5,name=NWIF01,busy=1
is VE88702PTC014
Returning tid_type(slot=0) tid_type.id=121 tid_type.drvr=0x6b1098
Returning tid_type(slot=0) tid_type.id=121 tid_type.drvr=0x6b1098
VP88702: SLIC terminatiotcb_alloc: task id=6,name=DQMM,busy=1
n type 10

tiuhw_setup_chipselect: cs for tcid 0 = 0 fxo: 33
tiuhw_setup_chipselect: cs for tcid 1 = 0 fxo: 33
Loading dsp image: /lib/dspimage.ld



========================================================
tcb_alloc: task id=7,name=ISU,busy=1
tcb_alloc: task id=8,name=VIM,busy=1
tcb_alloc: task id=9,name=CCU,busy=1
tcb_alloc: task id=10,name=RTCP,busy=1
tcb_alloc: task id=11,name=PMA,busy=1
tcb_alloc: task id=12,name=VLM,busy=1
tcb_alloc: task id=13,name=DEX,busy=1
DSPMOD query DSP address syscall: DSP Start address = 0x5FE00000
82: Disabling  PUMA DSPSS
85: Taking PUMA DSPSS IN  RESET
M5T E-DVA SDK 2.0.13.18 for Intel® Puma™6 SoC
Copyright(c) 2013 Media5 Corporation
Application built on Feb 11 2014 at 17:27:01
Library built on Feb 11 2014 at 17:26:41
========================================================


DSP external memory mapped to 0x04ED4000 (User Sp) = 0x5FE00000 (Kernel Sp)
dimhw_init_dsp: dpr_base mapped to 0x040D4000 (User sp)
tiuo_hw_init, tcid 0, timeslot 11
tiuo_hw_init, tcid 1, timeslot 12
ifconfig: SIOCSIFADDR: No such device
cmbs_api_Init: Mode:0 DevType:0 Port:2
cmbs_int_EnvCreate: MsgQId:0
Opened /dev/tts/2
cmbs_api_Init: data pump is started. ThreadId:93160624
cmbs_api_Init: call back thread started. ThreadId:102003888
cmbs_api_Init: Media is TDM interface

00:01:27.30000 ->> CMBS_CMD_HELLO [0x1, 13 bytes, #0]: 01 03 02 ff ff
cmbs_api_Init: Connecting target...

00:01:27.50000 <<- CMBS_CMD_HELLO_RPLY [0x2, 13 bytes, #0]: 30 03 d0 0c 00
TARGET API version: 03.30
TARGET BUItcb_alloc: task id=14,name=VOIMFE,busy=1
LD      : 0c.d0
TARGET mode       : 0

00:01:29.70000 -tcb_free: task id=4, name=ROOT
>> CMBS_EV_DSR_RF_SUSPEND [0x29, 8 bytes, #0]: FXS FXR = 16
Attempting to delete TCB: 4
XtDele82: Disabling  PUMA DSPSS
te called
lmxp85: Taking PUMA DSPSS IN  RESET
_tcb_free called for 4
pcd: (265): Rule VOICE_GGAPP: Success (Process /usr/sbin/M5tPc20Edva (764)).
pcd: (265): Rule VOICE_LASTRULE: Success.
pcd: (265): Rule PACM_INITDONE: Success.
pcd: (265): Starting process /usr/sbin/vendor_psm (Rule PACM_APPPSM).
pcd: (265): Starting process /usr/sbin/pacm_mta_control (Rule PACM_MTACTRL).
pcd: (265): Rule PACM_MTACTRL: Success (Process /usr/sbin/pacm_mta_control (854)).
pcd: (265): Rule PACM_APPPSM: Success (Process /usr/sbin/vendor_psm (853)).
pcd: (265): Rule PACM_LASTRULE: Success.
[INFO] [PACM.MTA_CONTROL(pid=764)]: PACM_MSMGetLoopVoltageStatusInit: Inform voice of voltage state Down
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - MAS Version: 3.0.0.0(Build 2)
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - Following features compiled out of the build:82: Enabling  PUMA DSPSS
85: Taking PUMA DSPSS OUT of  RESET

[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - 	DIM_DNLD_PAGED_BOOT
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - 	DIM_DNLD_DIRECT
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - 	DIM_DNLD_MSG
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - 	DIM_DNLD_RST_DIRECT
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - 	DIM_CHAN_IF
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - 	ANNC_IF
pcd: (265): Warning: Got READY event, but rule end condition is different.
PCD API: ICC wait return value -768
done setting mask 0x0
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - 	DIM_RTCP_IF
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - 	DIM_SIG_IF
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - 	DIM_AUDIO_IF
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - 	DIM_AFE_IF
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - 	DIM_LOMGR_GEN_FIFO
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - 	DIM_LOMGR_CHN_FIFO
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - 	DIM_LOMGR_MAIL_BOX
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - 	PROTO_AAL2
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - 	PROTO_CLRDT
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - 	PROTO_MODEM
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - 	DIM_3PROC
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - 	DIM_DETAILED_SPY
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - Following features not defined in build and have been enabled
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - by default; REVIEW to remove potential unecessary code:
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - 	All features are accounted for!!!
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - ISU: isu_module_init isu_event_base 0x0, task 0x00000000

[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - ISU: isu_create 0x00000007 queue 1

[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - CCU: ccu_module_init ccu_event_base 0x0, task 0x00000000

[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - CCU: ccu_create 0x00000009 queue 1 watchdog timer 2

[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - VLM: vlm_module_init vlm_event_base 0x0, task 0x00000000

[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - VLM: vlm_activate_vport_vl_config: vtcid: 0, ptcid_count: 2
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - VLM: vlm_activate_vport_vl_config: vtcid: 1, ptcid_count: 2
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - VLM: vlm_activate_vport_vl_config: vtcid: 2, ptcid_count: 1
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - VLM: vlm_activate_vport_vl_config: vtcid: 3, ptcid_count: 1
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - VLM: vlm_activate_vport_vl_config: vtcid: 4, ptcid_count: 1
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - DIM: status_request_period out of range [20 - 10000]
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - DIM: status_request_period set to default [1000]
[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - TIU max tcids = 7, poll mode = 0, poll period = 5

[ERROR] [VOICE.XSPY(pid=764)]: 0000002376 - TIU: Polling period must be multiple of 2 msec
[ERROR] [VOICE.XSPY(pid=764)]: 0000002555 - DIM: 0:*, dimp_find_and_init_lo_mgr(). max simple msg len (128) < sizeof(mgb_t)(146)
[ERROR] [VOICE.XSPY(pid=764)]: 0000002804 - DIM: 0:*, Core Download complete!
[ERROR] [VOICE.XSPY(pid=764)]: 0000002808 - DIM: 0:*, dimp_find_and_init_lo_mgr(). max simple msg len (128) < sizeof(mgb_t)(146)
[ERROR] [VOICE.XSPY(pid=764)]: 0000002812 - DIM:MAS_CFG_SLIC_WB_MODE_SUPPORT not supported
[ERROR] [VOICE.XSPY(pid=764)]: 0000002813 - DSPA: DSP 0,Image 0:Download done!
[INFO] [PACM.MTA_CONTROL(pid=854)]: starting main of PACM MSM.....
[INFO] [PACM.VOIM(pid=854)]: VoIM was initiated succesfully with ID 2056
[INFO] [PACM.MTA_CONTROL(pid=854)]: Starting TI_PACM_MODULE_MSM
[INFO] [PACM.VENDOR_APP(pid=853)]: setting isr mask 00000000
[WARNING] [PACM.VENDOR_APP(pid=853)]: Cannot read /proc/avalanche/ddr_sync_state
[WARNING] [PACM.VENDOR_APP(pid=853)]: DDR is not in Async mode, clock reduction will not be performed
[INFO] [PACM.MTA_CONTROL(pid=854)]: Setting IPv6 Support to docsis - True
[INFO_VERBOSE] [COMMON_COMPONENTS.GIM(pid=854)]: nid=8192: type SRN with 0 bytes data
[INFO] [PACM.VENDOR_APP(pid=689)]: vendor_app: received message from MSM (pacmMsg.msgID=0)
[INFO] [PACM.VENDOR_APP(pid=689)]: vendor_app: Disabled
[INFO] [PACM.MTA_CONTROL(pid=854)]: Registering on BBU system
[INFO] [PACM.MTA_CONTROL(pid=689)]: send response message ID 0
[INFO] [PACM.MTA_CONTROL(pid=854)]: LOOPV: Setting loop voltage status ON
[ERROR] [VOICE.XSPY(pid=764)]: 0000003079 - TIU:  dummy control called
[ERROR] [VOICE.XSPY(pid=764)]: 0000003079 - TIU:  dummy control called
[ERROR] [VOICE.XSPY(pid=764)]: 0000003079 - TIU:  dummy control called
[ERROR] [VOICE.XSPY(pid=764)]: 0000003079 - TIU:  dummy control called
[ERROR] [VOICE.XSPY(pid=764)]: 0000003080 - TIU:  dummy control called
[ERROR] [VOICE.XSPY(pid=764)]: 0000003080 - TIU:  dummy control called
[ERROR] [VOICE.XSPY(pid=764)]: 0000003080 - TIU:  dummy control called
[ERROR] [VOICE.XSPY(pid=764)]: 0000003080 - TIU:  dummy control called
[ERROR] [VOICE.XSPY(pid=764)]: 0000003080 - TIU:  dummy control called
[ERROR] [VOICE.XSPY(pid=764)]: 0000003080 - TIU:  dummy control called
[ERROR] [VOICE.XSPY(pid=764)]: 0000003080 - TIU:  dummy control called
[ERROR] [VOICE.XSPY(pid=764)]: 0000003081 - TIU:  dummy control called
[ERROR] [VOICE.XSPY(pid=764)]: 0000003081 - TIU:  dummy control called
[INFO_VERBOSE] [PACM.VOIM(pid=854)]: Recieved message Type = 13
[INFO] [PACM.VOIM(pid=854)]: VOIM: Received XGCP event (TCID=0, EventValue=18)
[INFO] [PACM.VOIM(pid=854)]: VOIM: send XGCP to /var/ledd_xgcp_unix successfully
[INFO] [DOCSIS.LEDD(pid=543)]: tel_xgcp_evt_hdl: index 0, event NMM_XGCP_EVENT_RE_REGISTERING(18), ac 1
[INFO] [DOCSIS.LEDD(pid=543)]: tel_proc_evt: [STATES (Sing)] alrm [0], line 1 [TEL_STATE_REGISTERING], line 2 [TEL_STATE_NOT_REGISTERED]
[INFO] [PACM.SNMP(pid=854)]: End point 0 doesn't appear in config file no change for eSafe.
[INFO_VERBOSE] [PACM.VOIM(pid=854)]: Recieved message Type = 13
[INFO] [PACM.VOIM(pid=854)]: VOIM: Received XGCP event (TCID=1, EventValue=18)
[ERROR] [PACM.VENDOR_APP(pid=853)]: PSM_WiFi_D_Bus_send_message, power=0
[INFO] [PACM.VOIM(pid=854)]: VOIM: send XGCP to /var/ledd_xgcp_unix successfully
[INFO] [PACM.SNMP(pid=854)]: End point 1 doesn't appear in config file no change for eSafe.
[INFO_VERBOSE] [PACM.VOIM(pid=854)]: Recieved message Type = 13
[INFO] [PACM.VOIM(pid=854)]: VOIM: Received XGCP event (TCID=2, EventValue=18)
[INFO] [DOCSIS.LEDD(pid=543)]: tel_proc_evt: not proved !!
[INFO] [PACM.VOIM(pid=854)]: VOIM: send XGCP to /var/ledd_xgcp_unix successfully
[INFO] [PACM.SNMP(pid=854)]: End point 2 doesn't appear in config file no change for eSafe.
[INFO_VERBOSE] [PACM.VOIM(pid=854)]: Recieved message Type = 13
[INFO] [PACM.VOIM(pid=854)]: VOIM: Received XGCP event (TCID=3, EventValue=18)
[INFO] [PACM.VOIM(pid=854)]: VOIM: send XGCP to /var/ledd_xgcp_unix successfully
[INFO] [PACM.SNMP(pid=854)]: End point 3 doesn't appear in config file no change for eSafe.
[INFO] [DOCSIS.LEDD(pid=543)]: tel_xgcp_evt_hdl: index 1, event NMM_XGCP_EVENT_RE_REGISTERING(18), ac 1
[INFO] [DOCSIS.LEDD(pid=543)]: tel_proc_evt: [STATES (Sing)] alrm [0], line 1 [TEL_STATE_REGISTERING], line 2 [TEL_STATE_REGISTERING]
[INFO_VERBOSE] [PACM.VOIM(pid=854)]: Recieved message Type = 13
[INFO] [PACM.VOIM(pid=854)]: VOIM: Received XGCP event (TCID=4, EventValue=18)
[INFO] [PACM.VOIM(pid=854)]: VOIM: send XGCP to /var/ledd_xgcp_unix successfully
[INFO_VERBOSE] [PACM.VOIM(pid=854)]: Recieved message Type = 13
[INFO] [PACM.VOIM(pid=854)]: VOIM: Received XGCP event (TCID=5, EventValue=18)
[INFO] [PACM.VOIM(pid=854)]: VOIM: send XGCP to /var/ledd_xgcp_unix successfully
[ERROR] [PACM.SNMP(pid=854)]: Failed to check if end point 5 appeared in the configuration file.
[INFO_VERBOSE] [PACM.VOIM(pid=854)]: Recieved message Type = 13
[INFO] [PACM.VOIM(pid=854)]: VOIM: Received XGCP event (TCID=6, EventValue=18)
[INFO] [DOCSIS.LEDD(pid=543)]: tel_proc_evt: not proved !!
[ERROR] [PACM.VENDOR_APP(pid=853)]: PSM_WiFi_D_Bus_send_message, power up popen ok
[INFO] [DOCSIS.LEDD(pid=543)]: tel_xgcp_evt_hdl: index 2, event NMM_XGCP_EVENT_RE_REGISTERING(18), ac 1
[INFO] [PACM.VOIM(pid=854)]: VOIM: send XGCP to /var/ledd_xgcp_unix successfully
[ERROR] [PACM.SNMP(pid=854)]: Failed to check if end point 6 appeared in the configuration file.
[INFO] [DOCSIS.LEDD(pid=543)]: tel_xgcp_evt_hdl: index 3, event NMM_XGCP_EVENT_RE_REGISTERING(18), ac 1
[INFO] [DOCSIS.LEDD(pid=543)]: tel_xgcp_evt_hdl: index 4, event NMM_XGCP_EVENT_RE_REGISTERING(18), ac 1
[INFO] [DOCSIS.LEDD(pid=543)]: tel_xgcp_evt_hdl: index 5, event NMM_XGCP_EVENT_RE_REGISTERING(18), ac 1
[INFO] [DOCSIS.LEDD(pid=543)]: tel_xgcp_evt_hdl: index 6, event NMM_XGCP_EVENT_RE_REGISTERING(18), ac 1
[INFO] [PACM.SNMP(pid=690)]: Setting Voice default configuration
[INFO] [PACM.SNMP(pid=690)]: Done Setting Voice default configuration, sending event MSM_ev_DefaultsSetted
[INFO] [PACM.VOIM(pid=854)]: Waiting until Voice init finishes
[INFO] [PACM.VOIM(pid=854)]: Voice Init done
[INFO_VERBOSE] [COMMON_COMPONENTS.GIM(pid=854)]: nid=8193: type SRN with 0 bytes data
[INFO] [PACM.MTA_CONTROL(pid=854)]: Starting MSM.....
[INFO] [PACM.MTA_CONTROL(pid=854)]: enter MSM_act_StartCM
[INFO] [PACM.MTA_CONTROL(pid=690)]: Sending Event MSM_ev_ConfigureDone, SNMP is ready.
[INFO] [DOCSIS.ESAFE(pid=854)]: Init ESAFE dev: 0 - mta0, RngholdoffMask 0x00000004, DHCP str EDVA, MAC Address 08:80:39:XX:XX:XX
[INFO] [DOCSIS.DMG(pid=605)]: DMG_guard_Enable:: DMG_EnableCtr == -1
[INFO] [DOCSIS.CHM(pid=548)]: Init 16 DOCSIS DS channels
[INFO] [DOCSIS.DS(pid=558)]: DSM [24] set to idle
[INFO] [DOCSIS.DS(pid=559)]: DSM [23] set to idle
[INFO] [DOCSIS.DS(pid=560)]: DSM [22] set to idle
[INFO] [DOCSIS.DS(pid=562)]: DSM [16] set to idle