WikiDevi will be going offline 2019-10-31. For historical dumps of the database, see 'WikiDevi' @ the Internet Archive (MW XML, Files, Images).
Final dumps will be made available after the site goes offline.
There is no chance the data will not live on, in some form - even if it isn't 'WikiDevi' anymore. For example, see TechInfoDepot.

Belkin F5D8235-4 v1

From WikiDevi
Jump to: navigation, search

Belkin F5D8235-4 v1

Manuf/OEM/ODM Gemtek WRTR-235GN

FCC approval date: 15 August 2008
UPC: 722868673799 (UPC DB, On eBay)
Country of manuf.: China

Type: wireless router

FCC ID: K7SF5D8235-4A
Industry Canada ID: 362A-F5D8235-4A

Power: 12 VDC, 1.5 A
Connector type: barrel

CPU1: Ralink RT2880 (266 MHz)
FLA1: 8 MiB
8,388,608 B
65,536 Kib
8,192 KiB
64 Mib
0.00781 GiB
(Macronix MX29LV640DBTC-90G)
RAM1: 32 MiB
33,554,432 B
262,144 Kib
32,768 KiB
256 Mib
0.0313 GiB
(Hynix HY57V281620FTP-6 × 2)

Expansion IFs: USB 2.0
USB ports: 1
Serial: yes, internal, 9-pin header, unpopulated, 3.3V TTL, Gemtek type1 pinout, (57600,8,N,1)

WI1 chip1: Ralink RT2880
WI1 chip2: Ralink RT2820
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: none

ETH chip1: Ralink RT2880
Switch: Realtek RTL8366SR
LAN speed: 1G
LAN ports: 4
WAN speed: 1G
WAN ports: 1

bgn

Stock FW OS: Linux 2.4.30

Flags: boot log

Default SSID: Belkin_N+_XXXXXX (3 addl. devices), Belkin_N+_Wireless_180170 (2 addl. devices)
Default IP address: 192.168.2.1
the IP 192.168.2.1 is used by 279 additional devices
of which 97 are Belkin devices

802dot11 OUI: 00:1C:DF (16 E, 32 W, 2007)
Ethernet OUI: 00:1C:DF (16 E, 32 W, 2007)

For a list of all currently documented Ralink chipsets with specifications, see Ralink.


N+ Wireless Router

 • Support page

Manuf. (and perhaps designed) by Gemtek, WRTR-235GN (WRTR-235GN_V01).

There is a NEC USB controller on-board.

The default SSID appears to be Belkin_N+_XXXXXX (where XXXXXX is replaced by the last three octets of the wireless interface MAC address [capital letters]).

When resetting to factory defaults, it seems the device temporarily assumes the SSID of Belkin_N+_Wireless_180170.
Belkin_N+_Guest is the default SSID for the guest network, but this is not enabled by default.

Serial[edit]

Pinout[edit]

    J6
      (   )
(GND) (RxD)
(GND) (   )   --> to copper shielding
(VCC) (   )
(VCC) [TxD]

Boot log[edit]

boot log
U-Boot 1.1.3 (Jun 12 2008 - 15:40:46)

Board: RT2880 DRAM:  32 MB
relocate_code Pointer at: 8bfa8000

 twe0 set to <NULL>
 toe0 set to <NULL>
flash_protect ON: from 0xBC400000 to 0xBC424D03
protect on 71
protect on 72
protect on 73
flash_protect ON: from 0xBC430000 to 0xBC43FFFF
protect on 74
*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 2.0
--------------------------------------------
ASIC 2880_MP (MAC to GigaMAC Mode)
DRAM COMPONENT: 128Mbits
DRAM BUS: 32BIT
Total memory: 32Mbytes
Date:Jun 12 2008  Time:15:40:46
============================================
 D-CACHE set to 4 way
 I-CACHE set to 4 way

 ##### The CPU freq = 266 MHZ ####

 SDRAM bus set to 32 bit
 SDRAM size =32 Mbytes

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   5: Load ucos code to SDRAM via TFTP.

You choosed 3

3: System Boot system code via Flash.
## Booting image at bc450000 ...
   Image Name:   Linux Kernel Image
   Created:      2008-08-22  11:25:09 UTC

 System Control Status = 0x02910084
   Image Type:   MIPS Linux Kernel Image (gzip compressed)
   Data Size:    1189525 Bytes =  1.1 MB
   Load Address: 8a000000
   Entry Point:  88244040
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 88244040) ...
## Giving linux memsize in MB, 32

Starting kernel ...

THIS IS ASIC - VERSION B
ramsize = 32 MBytes
rambase not set, set to default (0x08000000)
MEMORY DESCRIPTOR dump:
[0,882e3810]: base<08000000> size<02000000> type<Free RAM memory>

 The CPU feqenuce set to 266 MHz
CPU revision is: 0001906c
icache: sets:256, ways:4, linesz:16 ,total:16384, waybit:12, flags:0x0
dcache: sets:256, ways:4, linesz:16 ,total:16384, waybit:12, flags:0x0
i waysize = 4096, d waysize = 4096, i sets= 256, d sets=256
Primary instruction cache 16kB, physically tagged, 4-way, linesize 16 bytes.
Primary data cache 16kB, 4-way, linesize 16 bytes.
[setup_scache]:1032
Linux version 2.4.30 (root@localhost.localdomain) 
(gcc version 3.3.6) #294 Fri Aug 22 19:24:30 CST 2008
Determined physical RAM map:
 memory: 02000000 @ 08000000 (usable)
On node 0 totalpages: 40960
zone(0): 40960 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock2
cause = 70c08258, status = 10005c00
calculating r4koff... 0028b0aa(2666666)
CPU frequency 266.67 MHz
Using 133.333 MHz high precision timer.
Calibrating delay loop... 266.24 BogoMIPS
Memory: 28036k/32768k available (2311k kernel code, 4732k reserved, 232k data, 92k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
Checking for 'wait' instruction...  unavailable.
POSIX conformance testing by UNIFIX
pci.c pcibios_init():840
BAR0 at slot 0 = 8
pci.c pcibios_fixup_resources():640
bus = 0, dev = 0, fun = 0
pci.c pcibios_fixup_resources():640
bus = 0, dev = 17, fun = 0
pci.c pcibios_fixup_resources():748  devid=0x11, baseaddr = 0x14
pci.c pcibios_fixup_resources():748  devid=0x11, baseaddr = 0x18
pci.c pcibios_fixup_resources():748  devid=0x11, baseaddr = 0x1c
pci.c pcibios_fixup_resources():748  devid=0x11, baseaddr = 0x20
pci.c pcibios_fixup_resources():748  devid=0x11, baseaddr = 0x24
dev= 0x885fbc00
dev= 0x885e3000
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
fuse init (API version 7.5)
fuse distribution version: 2.5.3
pty: 256 Unix98 ptys configured
Ralink RT2880 gpio driver initialized
Gemtek LED init...
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x300500 (irq = 9) is a 16550A
ttyS01 at 0x300c00 (irq = 8) is a 16550A
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
RA2880 Ethernet Driver Initilization. v1.01  256 rx/tx descriptors allocated!
RA2880 Ethernet Driver Initilization. v1.01  256 rx/tx descriptors allocated, mtu = 4096!
Netlink init ok!
PROC INIT OK!
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
FLASH_API: MAN_ID=C2 DEV_ID=22CB SIZE=8MB
physmap flash device: 800000 at bf400000
 Amd/Fujitsu Extended Query Table v1.1 at 0x0040
number of CFI chips: 1
Region0: SectorSize=0x2000 SectorNum=8
Region1: SectorSize=0x10000 SectorNum=127
cfi_cmdset_0002: Using word write method.
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
Using physmap partition definition
Creating 5 MTD partitions on "RT2880 SOC Physically mapped flash":
0x00000000-0x00050000 : "uboot"
mtd: Giving out device 0 to uboot
0x00050000-0x007e0000 : "Kernel and Rootfs"
mtd: Giving out device 1 to Kernel and Rootfs
0x00180000-0x007e0000 : "Rootfs"
mtd: Giving out device 2 to Rootfs
0x007e0000-0x007f0000 : "Nvram"
mtd: Giving out device 3 to Nvram
0x007f0000-0x00800000 : "Factory"
mtd: Giving out device 4 to Factory
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
host/usb-uhci.c: $Revision: 1.1.1.1 $ time 19:24:30 Aug 22 2008
host/usb-uhci.c: High bandwidth mode enabled
host/usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
host/usb-ohci.c: USB OHCI at membase 0xc0801000, IRQ 2
host/usb-ohci.c: usb-00:11.0, PCI device 1033:0035
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 3 ports detected
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
Linux IP multicast router 0.06 plus PIM-SM
ip_conntrack version 2.1 (1280 buckets, 10240 max) - 316 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team, Type=Fully Cone
ipt_time loading
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
create_proc_read_write_entry: fail
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
FAT: bogus logical sector size 34816
UMSDOS: msdos_read_super failed, mount aborted.
FAT: bogus logical sector size 34816
FAT: bogus logical sector size 34816
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing prom memory: 0kb freed
Freeing unused kernel memory: 92k freed
console started
trying to start /sbin/init
trying to strt /etc/init
trying to start /bin/init
Algorithmics/MIPS FPU Emulator v1.5
MDIO_CFG = 1f01dc01
GDMA1_FWD_CFG = 90000
DSP_EN OFF version driver

phy_tx_ring = 09c64000, tx_ring = a9c64000, size: 16 bytes
phy_rx_ring = 09c43000, rx_ring = a9c43000, size: 16 bytes

BusyBox v1.1.0 (2008.08.22-10:56+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.

#sysinit: [sysinit]
# Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
MTD_open
MTD_ioctl
Invalid ioctl 540d (MEMGETINFO = 40204d01)
MTD_read
MTD_close
insmod: reset_btn.o: no module by that name found
Starting Watchdog function !!!!!!!
cat: /proc/watchdog_ctrl_folder/watchdog_ctrl_run: No such file or directory
/proc/sys/kernelMTD_open
/panic_on_oops: MTD_read
cannot create
MTD_close
Done
Clean storage nvram value!!
# update nvram with default list!
blink_status=0
Close USB_BLINK led...
# interfaces_init......
rmmod: rtl: Success
rtl_major = 253
0 smi_init check[0x0105]=0x8366
Gemtek Link status init.
rtl8366s_getEthernetPHY fail for 5!!!!
rtl8366s_getEthernetPHY fail for 6!!!!
rtl8366s_getEthernetPHY fail for 7!!!!
rtl8366s_getEthernetPHY fail for 8!!!!
rtl8366s_getEthernetPHY fail for 9!!!!
rtl8366s_getEthernetPHY fail for 10!!!!
rtl8366s_getEthernetPHY fail for 11!!!!
rtl8366s_getEthernetPHY fail for 12!!!!
rtl8366s_getEthernetPHY fail for 13!!!!
rtl8366s_getEthernetPHY fail for 14!!!!
rtl8366s_getEthernetPHY fail for 15!!!!
RTL8366RS driver SetVLan initialized
RTL8366RS driver initChip initialized
rtl8366s_getEthernetPHY fail for 5!!!!
rtl8366s_getEthernetPHY fail for 6!!!!
rtl8366s_getEthernetPHY fail for 7!!!!
rtl8366s_getEthernetPHY fail for 8!!!!
rtl8366s_getEthernetPHY fail for 9!!!!
rtl8366s_getEthernetPHY fail for 10!!!!
rtl8366s_getEthernetPHY fail for 11!!!!
rtl8366s_getEthernetPHY fail for 12!!!!
rtl8366s_getEthernetPHY fail for 13!!!!
rtl8366s_getEthernetPHY fail for 14!!!!
rtl8366s_getEthernetPHY fail for 15!!!!
RTL8366RS driver SetVLan initialized
vid 1 member:3e untag:1e
vid 2 member:21 untag:1
port=0,VID=2,priority=0
port=1,VID=1,priority=0
port=2,VID=1,priority=0
port=3,VID=1,priority=0
port=4,VID=1,priority=0
port=5,VID=1,priority=0
RTL_GET_GREEN_ETHERNET Success!!!
RTL_GET_GREEN_ETHERNET : tx is 0, rx is 0
RTL_GET_GREEN_ETHERNET : rtl8366s_getAsicPowerSaving is phyNo.0, enabled : 0 !!!
RTL_GET_GREEN_ETHERNET : rtl8366s_getAsicPowerSaving is phyNo.1, enabled : 0 !!!
RTL_GET_GREEN_ETHERNET : rtl8366s_getAsicPowerSaving is phyNo.2, enabled : 0 !!!
RTL_GET_GREEN_ETHERNET : rtl8366s_getAsicPowerSaving is phyNo.3, enabled : 0 !!!
RTL_GET_GREEN_ETHERNET : rtl8366s_getAsicPowerSaving is phyNo.4, enabled : 0 !!!
rtl:rtl_ge_read : 0
RTL_SET_GREEN_ETHERNET Success!!!
RTL_GET_GREEN_ETHERNET Success!!!
RTL_GET_GREEN_ETHERNET : tx is 1, rx is 1
RTL_GET_GREEN_ETHERNET : rtl8366s_getAsicPowerSaving is phyNo.0, enabled : 1 !!!
RTL_GET_GREEN_ETHERNET : rtl8366s_getAsicPowerSaving is phyNo.1, enabled : 1 !!!
RTL_GET_GREEN_ETHERNET : rtl8366s_getAsicPowerSaving is phyNo.2, enabled : 1 !!!
RTL_GET_GREEN_ETHERNET : rtl8366s_getAsicPowerSaving is phyNo.3, enabled : 1 !!!
RTL_GET_GREEN_ETHERNET : rtl8366s_getAsicPowerSaving is phyNo.4, enabled : 1 !!!
rtl:rtl_ge_read : 1
Setting ra0 configuration....
Bring up ra0 interface....
2860 version : 1.8.3.0 (Aug 22 2008)

=== pAd = c0948000, size = 483400 ===

<-- RTMPAllocAdapterBlock, Status=0
RX DESC a969b000  size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
1. Phy Mode = 9
2. Phy Mode = 9
3. Phy Mode = 9
MCS Set = ff ff 00 00 00
Main bssid = 00:1c:df:d4:3d:38
The UUID Hex string is:2880288028801880a880001cdfd43d38
The UUID ASCII string is:28802880-2880-1880-a880-001cdfd43d38!
<==== RTMPInitialize, Status=0
0x1300 = 00064380
interface ra0 does not exist!
No need to change ra0 to Nintendo NDS capable
No need to change ra0 to Nintendo NDS capable...Complete
killall: rt2860apd: no process killed
rt2860apd: not found
Mssid : init mode
killall : No such file or directory
get_WPS_PIN_code : WSCStatus : 39093042
check_WPS_status : WSCStatus is 3 now...STATUS_WSC_LINK_UP
WPS BUTTON press!!
killall: wscd: no process killed
route: SIOC[ADD|DEL]RT: No such device
ra0       mac:
[0x0000102c]:73031e46
vlan1: Setting MAC address to  00 1c df d4 3d 38.
device eth2 entered promiscuous mode
VLAN (vlan1):  Setting underlying device (eth2) to promiscious mode.
vlan1: dev_set_promiscuity(master, 1)
device vlan1 entered promiscuous mode
device ra0 entered promiscuous mode
ra0: attempt to add interface with same source address.
gPassiveMsgQ Init success! gPassiveMsgID=0x386d438b!
gActiveMsgQ Init success!
br0: port 2(ra0) entering listening state
br0: port 1(vlan1) entering listening state
sock=5!(0x0x7fff7d10)
# lan services init......
Pthread(wscDevNLHandle)Now waiting for the netlink socket incoming message!
Create netlink socket thread success!
Create ioctl socket(6) success!
killall: rt2860apd: no process killed
rt2860apd: No such file or directory
Start UPnP
easyconf: start 20080820
easyconf: Waiting for client to connect...
route: resolving gw
route: resolving gw
route: resolving gw
route: resolving gw
route: resolving gw
br0: port 2(ra0) entering learning state
br0: port 1(vlan1) entering learning state
wscd: SSDP UDP PORT = 1900
Error with UpnpInit -- -208
killall : No such file or directory
get_WPS_PIN_code : WSCStatus : 39093042
check_WPS_status : WSCStatus is 3 now...STATUS_WSC_LINK_UP
br0: port 2(ra0) entering forwarding state
br0: topology change detected, propagating
br0: port 1(vlan1) entering forwarding state
br0: topology change detected, propagating
killall: wscd: no process killed
route: SIOC[ADD|DEL]RT: File exists
(2112)Service enable wireless
# wan_init......
Set country code to us!!!
gPassiveMsgQ Init success! gPassiveMsgID=0x386d438d!
gActiveMsgQ Init success!
sock=5!(0x0x7fff7d10)
Create netlink socket thread success!
Create ioctl socket(6) success!
Pthread(wscDevNLHandle)Now waiting for the netlink socket incoming message!
vlan2: Setting MAC address to  00 1c df d4 3d 3a.
(wscDevNLHandle):netlink socket data is available now.
wscNLEventRTMNewlinkHandlewscd: SSDP UDP PORT = 1900
Close speed boot up led...
UPnP Initialized
         IP-Addr: 192.168.2.1 Port: 49152
         HW-Addr: 00:1c:df:d4:3d:38!
Specifying the webserver root directory -- /etc_ro/xml/
UUID Str=uuid:28802880-2880-1880-a880-001cdfd43d38!
alloc memory size=1135!
<?xml version="1.0" encoding="utf-8"?>
<root xmlns="urn:schemas-upnp-org:device-1-0">
  <specVersion>
    <major>1</major>
    <minor>0</minor>
  </specVersion>
  <device>
    <deviceType>urn:schemas-wifialliance-org:device:WFADevice:1</deviceType>
    <friendlyName>Belkin Wireless Router</friendlyName>
    <manufacturer>Belkin Corporation</manufacturer>
    <manufacturerURL>http://www.belkin.com</manufacturerURL>
    <modelDescription>Belkin Wireless Router</modelDescription>
    <modelName>Belkin Wireless Router</modelName>
    <modelNumber>F5D</modelNumber>
    <modelURL>http://www.belkin.com</modelURL>
    <serialNumber>111111111111</serialNumber>
<UDN>uuid:28802880-2880-1880-a880-001cdfd43d38</UDN>
    <serviceList>
      <service>
        <serviceType>urn:schemas-wifialliance-org:service:WFAWLANConfig:1</serviceType>
        <serviceId>urn:wifialliance-org:serviceId:WFAWLANConfig1</serviceId>
        <SCPDURL>WFAWLANConfigSCPD.xml</SCPDURL>
        <controlURL>control</controlURL>
        <eventSubURL>event</eventSubURL>
      </service>
    </serviceList>
  </device>
</root>

Registering the RootDevice
         with descDocUrl: http://192.168.2.1:49152/description.xml
RootDevice Registered
WscLocalDevice:
        Device:
                FriendlyName=Belkin Wireless Router!
                DescDocURL=http://192.168.2.1:49152/description.xml!
                UDN=uuid:28802880-2880-1880-a880-001cdfd43d38!
                PresURL=!
        Service:
                servIdStr=urn:wifialliance-org:serviceId:WFAWLANConfig1!
                servTypeStr=urn:schemas-wifialliance-org:service:WFAWLANConfig:1!
                scpdURL=http://192.168.2.1:49152/WFAWLANConfigSCPD.xml!
                eventURL=http://192.168.2.1:49152/event!
                controlURL=http://192.168.2.1:49152/control!
WscLocalDeviceInit Initialized
Changing password for guest
Bad password: too short.

Warning: weak password (continuing).
Jan  1 00:00:14 passwd[264]: password for `guest' changed by user `root'
Password changed.
Advertisement Sent
Can't load /etc/smb.conf - run testparm to debug it
httpd : This is httpd...ssl_enabled is 0

Info[edit]

cat /proc/mtd[edit]

# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00050000 00010000 "uboot"
mtd1: 00790000 00010000 "Kernel and Rootfs"
mtd2: 00660000 00010000 "Rootfs"
mtd3: 00010000 00010000 "Nvram"
mtd4: 00010000 00010000 "Factory"

cat /proc/cpuinfo[edit]

# cat /proc/cpuinfo
system type      : Palmchip Surfboard
processor        : 0
cpu model        : unknown V6.12
BogoMIPS         : 266.24
wait instruction : no
microsecond timers      : yes
tlb_entries      : 16
extra interrupt vector  : yes
hardware watchpoint     : no
VCED exceptions  : not available
VCEI exceptions  : not available

lsmod[edit]

# lsmod
Module                  Size  Used by    Tainted: P
rt2860v2_ap           988920  1
rtl                    83616  0
usb-storage            70240  0 (unused)

ps[edit]

ps
# ps
  PID  Uid     VmSize Stat Command
    1 root        236 S   /bin/init
    2 root            SW  [keventd]
    3 root            SWN [ksoftirqd_CPU0]
    4 root            SW  [kswapd]
    5 root            SW  [bdflush]
    6 root            SW  [kupdated]
   10 root            SW  [mtdblockd]
   11 root            SW  [khubd]
   19 root        416 S   /bin/sh
   38 root        480 S   resetC
   42 root        776 S < gpio_ctrl
   44 root        384 S   psmon
   95 root            SW  [rtmpWscHandle]
  154 root        340 S   syslogd
  156 root        392 S < httpd
  165 root        220 S   easyconf
  166 root        236 S   easytest 192.168.2.1 234.2.2.9 14675
  168 root        296 S   easystorage
  172 root        892 S   /usr/sbin/udhcpd /tmp/udhcpd.conf
  186 root        912 S   /usr/sbin/upnp -D -L br0 -W vlan2
  198 root        412 S   dnsmasq -z br0 -n -o -u root -r /var/resolv.conf -H /
  213 root        696 S   /usr/sbin/wscd -i ra0 -m 1 -d 3
  215 root        696 S   /usr/sbin/wscd -i ra0 -m 1 -d 3
  218 root        920 S   ledctrl
  219 root        696 S   /usr/sbin/wscd -i ra0 -m 1 -d 3
  224 root        696 S   /usr/sbin/wscd -i ra0 -m 1 -d 3
  225 root        696 S   /usr/sbin/wscd -i ra0 -m 1 -d 3
  228 root        696 S   /usr/sbin/wscd -i ra0 -m 1 -d 3
  233 root        272 S   if_traffic
  235 root        864 S   wan_connect
  242 root        696 S   /usr/sbin/wscd -i ra0 -m 1 -d 3
  249 root        696 S   /usr/sbin/wscd -i ra0 -m 1 -d 3
  254 root        696 S   /usr/sbin/wscd -i ra0 -m 1 -d 3
  255 root        696 S   /usr/sbin/wscd -i ra0 -m 1 -d 3
  265 root        340 S   lld2d br0
  542 root       1384 S   /usr/local/samba/sbin/nmbd
  570 root       1500 S   /usr/local/samba/sbin/smbd
 1410 root        340 R   ps

cat /proc/meminfo[edit]

meminfo
# cat /proc/meminfo
        total:    used:    free:  shared: buffers:  cached:
Mem:  28803072 20930560  7872512        0  1978368  8519680
Swap:        0        0        0
MemTotal:        28128 kB
MemFree:          7688 kB
MemShared:           0 kB
Buffers:          1932 kB
Cached:           8320 kB
SwapCached:          0 kB
Active:           4380 kB
Inactive:         5928 kB
HighTotal:           0 kB
HighFree:            0 kB
LowTotal:        28128 kB
LowFree:          7688 kB
SwapTotal:           0 kB
SwapFree:            0 kB

nvram show[edit]

Belkin F5D8235-4 v1/nvram

Images[edit]