WikiDevi will be going offline 2019-10-31. For historical dumps of the database, see 'WikiDevi' @ the Internet Archive (MW XML, Files, Images).
Final dumps will be made available after the site goes offline.
There is no chance the data will not live on, in some form - even if it isn't 'WikiDevi' anymore. For example, see TechInfoDepot.
ASUS RT-N12 rev B1
"P/N: 141700520029J R0B" is silkscreened on the board in the FCC photos.
- The Arcadyan model on the label is WG7005F22 1-ASU.
Links of Interest
- 5dBi antennas
- 14:DA:E9 (ASUStek) OUI
Console port J3 uses 3.3 V signaling at speed 115200.
- Header is pre-installed.
Pin 2 - TX, Pin 3 - RX, Pin 4 - GND
|NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power.|
Supported by dd-wrt as of dd-wrt.v24-17990
This install needs to be updated, I just wanted to get the page started.
Asus RT-N12 is now supported. Actually it is quite good router for its price.
If you don't need USB and Giga ethernet and 5GHz, it is good alternative
- to e.g. Linksys wrt160nv3 etc..
It has bcm4716b0 cpu, 4MB flash and 32MB ram + 2 external removable antennas.
- Please don't flash any old builds.
Ok, here it is.. something to start with... then simple GUI update will do.
For Revision B1 of the RT-N12B1 devices use this firmware image:
- There is also a revision ASUS RT-N12 rev C1 of the hardware.
Check the label on the bottom of your device or view the Top left of the original ASUS firmware for your hardware revision.
- Do not flash the initial firmware for a different revision of hardware than yours.
- You may still be able to recover your device if it enters an infinite reboot loop
- using recovery mode as a result of loading incompatible firmware.
- (Hold recover button for 30 seconds when applying the power, with static IP
- settings on your computer connected via ethernet)
To clear NVRAM hold down the WPS button when applying power for 30 seconds on all the RT-N12 models.
0. Download the firmware above and extract it to your desktop or a convenient location.
1. For simplicity, connect only the PC to one of the router's LAN ports with a normal [uplink] ethernet cable.
- No other modem,computers,routers,switches, etc should be connected.
2. In order to prevent DHCP from interupting the connection, you will need to manually set the address of your PC's Network
- LAN card to a STATIC IP in the same subnet of the router, such as 192.168.1.10 with subnet mask 255.255.255.0 .
Also make sure all other adapters,such as wireless, which might be seen as "clients" by the router are disabled.
- Only the main LAN connection [IP: 192.168.1.10] should be able to communicate with the router.
3. Unplug the power connector from the back of the router.
4. While pushing & holding the recessed Restore button on the back of the router,
- plug the power connector back in. The Restore button is NOT the raised red WPS button.
5. When the power LED slowly blinks on and off, release the Restore button.
- The router is now in "RESCUE MODE".
6. Use the Asus Firmware Restoration Utility [which you should have installed on the PC]
- to upload the DD-WRT mini-asus.trx file from the location where you saved it.
7. After the upgrade, the Utility should ask for a router reboot.
- Give it AT LEAST a minute to be on the safe side before removing the power.
Then unplug the power from the router, wait 10 seconds or so and plug the power back in.
- You should now be able to access the web interface.
8. Return your Net adapter properties for TCP/IP to DHCP "Automatically Obtain IP"
9. Type 192.168.1.1 into your browser and set your username as root and pick a password.
ALTERNATE INSTALLATION METHOD FOR ASUS TO DD-WRT FW UPDATE
- The steps listed above did not work for me, but these steps did.
1) Disconnect all ethernet cables from the RT-N12 except 1 going to your NIC.
2) Turn off all wireless clients (notebooks, PS3 etc...).
2a) Turn off all programs on your computer that may be trying to access the internet
- - e.g. open browser tabs, IM software, etc.
3) Ensure DHCP is enabled in the ASUS firmware and retreive IP/DNS automatically is set in your NIC properties.
- (When you open your IE browser it will instruct you to plug back in your WAN ISP cable,
if your PC is still seeing the router. If not, you may need to reboot router and/or PC.)
4) Do the 30/30/30 peacock method of putting your router in recovery mode.
5) Open the router IP of 192.168.1.1. The page will open to a built in browser (HTTP) recovery console.
6) Click on the link below Reboot to reset/flash the Vram.
7) Click the Browse button to browse to your DD-WRT firmware file location.
8) Click the Upload button.
The router will upload the file fairly quickly, and you will be brought to the next
- screen that says "Allow router time to reboot." BE PATIENT this takes about 4-5 minutes.
You will see the LAN1 light turn off and notice the "Network Cable Unplugged" windows popup
- message in task bar. Wait for the light to turn back on and the PC to reconnect to router.
9) Click the "Continue" link shown on the page.
- Clicking "Continue" forces the router to perform another reboot.
When it comes back up you will be at the DD-WRT admin login screen.
If the login screen is white and looks very basic you will need toperform another reboot of the router by removing the power cable.
- 'Asus Tomato Flash Guide
Note: some people say you need to install DD-WRT first. I do NOT recommend anyone to install DD-WRT first before installing Tomato on Asus routers.
- Download a suitable tomato firmware
- Install the Asus router utility from the CD that came with the router. Run \Utility\setup.exe from the CD to install it. If you no longer have the CD you can also download it from the Asus website.
- Disable Firewall on your computer.
- Disable anti-virus on your computer.
- Connect your computer to one of the LAN ports of the router with an ethernet cable.
- Assign a static IP of 192.168.1.10 and subnet mask 255.255.255.0 to your computer LAN port.
- Disconnect the router WAN port if you already have a cable plugged into that port.
- From Windows Start menu, run ASUS Utility -> RT-N Wireless Router -> Firmware Restoration.
- Click the Browse button and select the file that you downloaded in step #1. Don’t click the upload button yet.
- Put the router in recovery mode: Unplug the power cord of the router. Hold down the black Restore button using a pen (not the red button). Plug the power cord back in. Once the power light starts flashing slowing, release the Restore button. The power light should continue to flash. The flashing light means the router is ready to accept the new firmware in recovery mode.
- Click the upload button in the Restoration utility. If it warns about incorrect Asus firmware, ignore it. The firmware should now start uploading into the router. Don’t touch anything while the firmware is being uploaded. (Note: these steps worked when I flashed my RT-N16. However, the utility could not find my RT-N12 B1 when I tried to flash the router, although it did work for other people. After failing for more than a dozen times, I tried to perform the upload first before putting the router in recovery mode, then it finally worked. Later I tried a different unit of RT-N12 B1 strangely it could be flashed the first time using the normal procedure. If neither of these procedures work, please see the Addendum in The Wiert Corner, and the tftp method described by Simeon W in the comments section.)
- No matter whether the utility says the upload is completed, or it hangs at a certain percent, DO NOT PANIC, and WAIT FOR FIVE MINUTES before you do anything else.
- After five minutes, open a browser and go to http://192.168.1.1. Login with user “admin” (or “root”) and password “admin”. You should be logged into Tomato.
- Administration -> Configuration -> Restore Default Configuration -> Erase all data in NVRAM memory(thorough) -> OK (Note: there is a forum report saying this reset function does not work properly on RT-N53 – in this case, try the hardware reset button.)
- After it is completed, login again, enable DHCP (for Toastman Builds), change admin password, enable WiFi security if you use WiFi, plug in your WAN connection and configure it. Also take a look at the CPU frequency, you may need to manually change it if it is not correct. (Note: overclocking your router is usually not a good idea from my experience.)
- Change your computer LAN port back to use DHCP (dynamic address) and dynamic DNS.
Wiert Corner method
- pull the power plug on the RT N66U
- press and hold the reset button
- insert the power plug on the RT N66U
- wait for the power led to slowly blink
- release the reset button
- wait a few minutes for the modem to become stable
- in the mean time set your PC to these IPv4 settings: – host =
192.168.1.100– mask =
- start your web-browser
- point your web-browser to
http://192.168.1.1(it will time out, don’t worry)
- press the power button to turn off the router
- wait a few seconds
- press the power button to turn on the router now your router gets into rescue mode
- refresh your browser so it goes to
- upload your Tomato firmware
Put the router into recovery mode, set a static IP address on the computer then run in the shell:Wait several minutes while firmware transfers and router updates. Reboot twice, waiting 3 minutes in between each reboot, and the router should now have tomato installed.